English
GREAT BRITAIN •
customer service
tel:
020 8247 9300
internet
www.clasohlson.co.uk
postal
10 – 13 Market Place, Kingston Upon Thames, Surrey, KT1 1JZ
1
2
3
4
5
6
Ver
. 20170920
Solar Bollard Rattan Light
Art.no 36-6943 Model ZK6303
Please read the entire instruction manual before use and
then save it for future reference. We reserve the right for any
errors in text or images and any necessary changes made
to technical data. In the event of technical problems or other
queries, please contact our Customer Services.
Safety
Important
• Handle the product with care, making sure not to damage
the surface of the solar cell and ensuring that it is not
covered with dust or affected by other contaminants.
• Never attempt to repair or modify the product in any way.
• Repairs must only be carried out by authorised service
personnel and only using genuine spare parts.
• The battery must only be replaced with a rechargeable battery.
• Never let children play with the product.
Product description
1. Top section (contains solar
cell, light, power switch and
battery)
2. Upper light emitter
3. Middle section
4. Lower light emitter
5. Base
6. Ground spike
Assembly & Use
Note
• When placing the product outdoors, make sure that it has
access to maximum sunlight and is not affected by other
light sources such as street lights.
• When the battery is fully charged, the light will shine for
approximately 8 hours in the dark.
1. Dismantle the parts of the bollard (refer to the
Product
description
section, 1–6).
2. Place the base (5) on a level surface such as a deck or lawn.
3. Fasten the base to the underlying surface so that the bollard
stands steady. There are two ways to do this, depending on
the type of underlying surface:
-
A hard surface, such as stone/wood: Place a weight
(stone or similar) in the bottom of the base.
-
A soft surface such as grass: Push the ground spike (6)
through the hole in the bottom of the base and push it
into the ground. Add a weight to the bottom of the base
if required.
4. Fit the lower light emitter (4) onto the base.
5. Fit the middle section (3) onto the lower light emitter.
3. Take out the plate and turn it
around. Be careful not to damage
the cables and the circuit board.
4. Change the battery and make sure
that it is inserted with the correct
polarity.
6. Fit the upper light emitter (2) onto
the middle section.
7. Set the power switch on the under-
side of the top section (1) to
ON
.
8. Fit the top section onto the upper
light emitter.
9. The lamp comes on automatically
at dusk.
Care and maintenance
• Clean the product using a slightly damp cloth. Use only mild
cleaning agents, never solvents or corrosive chemicals.
• Replacing the battery, when required:
1. Lift off the top section.
2. Remove the 4 screws on
the underside of the top section.
Troubleshooting guide
What to do if the lamp does not shine:
• Check that the power switch is in the
ON
position.
• The battery is discharged. Make sure the bollard is exposed
to sunlight.
• The solar cell is dirty. Clean it by wiping with a damp cloth.
Responsible disposal
This symbol indicates that this product should not
be disposed of with general household waste.
This applies throughout the entire EU. In order
to prevent any harm to the environment or
health hazards caused by incorrect waste
disposal, the product must be handed in for
recycling so that the material can be disposed
of in a responsible manner. When recycling
the product, take it to your local collection facility
or contact the place of purchase. They will
ensure that the product is disposed of in
an environmentally sound manner.
Specifications
Rechargeable battery
1 × AA/HR6 NiMH 800 mAh
Charging time
8 hours (in continuous sunlight)
Operating time
8 hours (when fully charged)
Operating temperature
−10 to 50 ºC
Size
58.5 × 15 × 15 cm
