Draper WTL330A Instructions Manual Download | Manualshive

Page: 1 / 24

background image

INSTRUCTIONS FOR

250W 230V 300mm

Variable Speed Mini WoodLathe

Stock No.60988

Part No.WTL330A

IMPORTANT:

PLEASE READ THESE INSTRUCTIONS CAREFULLY TO ENSURE THE SAFE AND

EFFECTIVE USE OF THIS PRODUCT.

GENERAL INFORMATION

GENERAL INFORMATION

These instructions accompanying the product are the original instructions. This document is part of the product, keep it
for the life of the product passing it on to any subsequent holder of the product. Read all these instructions before
assembling, operating or maintaining this product.
This manual has been compiled by Draper Tools describing the purpose for which the product has been designed, and
contains all the necessary information to ensure its correct and safe use. By following all the general safety instructions
contained in this manual, it will ensure both product and operator safety, together with longer life of the product itself.
AlI photographs and drawings in this manual are supplied by Draper Tools to help illustrate the operation of the product.
Whilst every effort has been made to ensure the accuracy of information contained in this manual, the Draper Tools
policy of continuous improvement determines the right to make modifications without prior warning.

1
2
3
...
»

Summary of Contents for WTL330A

























Reviews:

No comments

Related manuals for WTL330A

Brand: Sealey Pages: 5

Brand: Sealey Pages: 7

Brand: Sealey Pages: 7

Brand: Sealey Pages: 12

Brand: mori seiki Pages: 296

Brand: Raider Pages: 74

Brand: Mac Afric Pages: 24

Brand: CabKing Pages: 20

Brand: Milltronics Pages: 93

Brand: Grizzly Pages: 12

Brand: Grizzly Pages: 96

Brand: Laguna Tools Pages: 32

BORING SYSTEM 35

Brand: Maggi Pages: 66

Brand: YoraHome Pages: 68

Brand: Jet Pages: 2

Brand: Jet Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands