![background image](http://html.mh-extra.com/html/sealey/sm2503/sm2503_instructions-manual_1225404001.webp)
Refer to
instruction
manual
Wear eye
protection
Wear ear
protection
Wear
protective
clothing
INSTRUCTIONS FOR:
MULTI FUNCTION MACHINE
MODEL NO:
SM2503
1. SAFETY
1.2 GENERAL SAFETY
WARNING!
Disconnect the multi function machine from the mains power, and ensure the cutting tool or chuck is at a complete standstill before attempting
to change accessories, service or perform any maintenance.
Maintain the
multi function machine in good condition (use an authorised service agent).
Replace or repair damaged parts.
Use recommended parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
Locate the multi function machine in a suitable area. Ensure the surface is flat and firm. Keep area clean and tidy and free from unrelated materials, and
ensure there is adequate lighting.
Keep the multi function machine clean for best and safest performance and check moving parts alignment regularly.
WARNING!
Before each use check that drill/chuck/cutting tool is secure and that it is not worn or damaged. If worn or damaged replace immediately.
WARNING!
Keep guard and holding fixings in place, tight and in good working order. Check regularly for damaged parts.
A guard, or any other part, that is damaged must be replaced with a new one, to ensure that it operates properly and performs its intended function, before the tool is
used. The safety guard is a mandatory fitting where multi function machine is used in premises covered by the Health & Safety at Work Act.
Remove adjusting keys and wrenches from the machine and its vicinity before turning it on.
WARNING!
Wear approved safety eye protection and, if oil mist is generated, respiratory protection.
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.
Keep hands and body clear of the work table when operating the multi function machine.
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
Always clamp workpiece securely to the table or hold securely in a vice which is firmly mounted to the table. NEVER hold a workpiece by hand. Ensure that
workpieces to be turned are held securely in the chuck. Long workpieces should be held at both ends and along their length with suitable steady rests.
Keep children and unauthorised persons away from the working area.
WARNING!
DO NOT switch the multi function machine on whilst the drill or cutting tool is in contact with the workpiece. Bring the drill or cutting tool gradually
to the workpiece. Avoid un-intentional starting of the multi function machine.
DO NOT force the multi function machine to achieve a task it was not designed to perform.
DO NOT allow untrained persons to operate the multi function machine.
DO NOT get the multi function machine wet or use in damp or wet locations or areas where there is condensation.
WARNING!
DO NOT
use multi function machine where there are flammable liquids, solids or gases such as petrol, paint solvents, waste wiping rags etc.
DO NOT operate the multi function machine if any parts are missing or damaged as this may cause failure and/or possible personal injury.
DO NOT remove the safety guard whilst in use.
DO NOT attempt to remove a workpiece until the drill, cutting tool or chuck has stopped rotating.
DO NOT touch the workpiece close to the cut as it will be very hot. Allow to cool.
DO NOT leave the drill or cutting tool operating unattended.
DO NOT operate the drill or cutting tool when you are tired or under the influence of alcohol, drugs or intoxicating medication.
When not in use switch the drilling/milling machine off and isolate from the power supply.
1.1.
ELECTRICAL SAFETY
WARNING!
It is the responsibility of the owner and the operator to read, understand and comply with the following: You must check all electrical products,
before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and any other connectors for wear or damage. You must ensure that the
risk of electric shock is minimised by the installation of appropriate safety devices. A Residual Current Circuit Breaker (RCCB) should be incorporated in the main
distribution board. We also recommend that a Residual Current Device (RCD) is used. It is particularly important to use an RCD with portable products that are
plugged into a supply which is not protected by an RCCB. If in any doubt consult a qualified electrician. You may obtain a Residual Current Device by contacting
your Sealey dealer.
You must
also read and understand the following instructions concerning electrical safety.
1.1.1. The
Electricity at Work Act 1989
requires all portable electrical appliances, if used on business premises, to be tested by a qualified electrician, using
a Portable Appliance Tester (PAT), at least once a year.
1.1.2. The
Health & Safety at Work Act 1974
makes owners of electrical appliances responsible for the safe condition of those appliances and the safety of
the appliance operators.
If in any doubt about electrical safety, contact a qualified electrician.
1.1.3. Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply. See 1.1.1.
and 1.1.2. and use a Portable Appliance Tester.
1.1.4. Ensure that cables are always protected against short circuit and overload.
1.1.5. Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that none is loose.
1.1.6.
Important:
Ensure that the voltage marked on the appliance matches the power supply to be used and that the
1.1.7.
DO NOT
pull or carry the appliance by the power cable.
1.1.8.
DO NOT
pull the plug from the socket by the cable.
1.1.9.
DO NOT
use worn or damaged cables, plugs or connectors. Immediately have any faulty item repaired or replaced by a
qualified electrician.
When a BS 1363/A UK 3 pin plug is damaged, cut the cable just above the plug and
dispose of the plug safely.
Fit a new plug according to the following instructions (UK only).
a) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.
b) Connect the BROWN live wire to the live terminal ‘L’.
c) Connect the BLUE neutral wire to the neutral terminal ‘N’.
d) After wiring, check that there are no bare wires, that all wires have been correctly connected,
that the cable outer insulation extends beyond the cable restraint and that the restraint is tight.
1.1.10. If an extension reel is used it should be fully unwound before connection. A reel with an RCD fitted is preferred since any appliance plugged into it will
be protected. The cable core section is important and should be at least 1.5mm², but to be absolutely sure that the capacity of the reel is suitable for this
product and for others which may be used in the other output sockets, we recommend the use of 2.5mm² section cable.
Original Language Version
SM2503 Issue: 3 - 18/07/17
Replacement fuse
rating: 5A
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT
CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL
INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions and maintained properly, give you years of trouble free performance.
© Jack Sealey Limited