manualshive.com logo in svg
background image

 

DSEDPM144-5LVA Rev 10/20 

Directive Systems & Engineering 

                     2702 Rodgers Terrace

 

              Haymarket, VA 20169-1628 

                             www.directivesystems.com 
                                      703-754-3876 

 

5 Element 144-148 MHz (Rear/Center Mount) Yagi,  

Model DSEDPM144-5LVA 

                                                                 

 

                                                      ELECTRICAL SPECIFICATIONS

 

                                         

             Frequency range: MHz ..................... 144-148 

 

Gain: dBd...........................................  9.0 

 

Impedance: Ohms.............................. 50 

 

Connector type................................... Type N(F) UG-58/U 

 

Front -to- back ratio: dB...................... 20 

 

SWR: Typical at resonance................ 

1.2:1 

 

Beamwidth: -3 degrees 

 

E- Plane ................................. 52° 

        -10 dB ................................. 89.6° 

 

 

H- Plane ................................. 65° 

 

Sidelobe level: decibels 

 

E- Plane ................................. -17 

 

H- Plane ................................. -16 

 

Power rating, Continuous: Watts ......   1500 

 

Stacking Distance: in.(m) 

 

             E- Plane.................................. 72

” (1.829) 

      

              H- Plane.................................  66

” (1.676) 

 

 

     MECHANICAL SPECIFICATIONS 

 

   Boom length: in. (m.)........................... 67

” (1.7) 

   Turning radius: in. (m.)........................ 34

” (.863) 

  Weight Assembled: Lbs (kg.).............. 2.8 (1.27) 
  Max mast size: in. (cm.).......................2

” (5.08) 

  Wind surface area: Ft

2

 (m.

2

) ............... 0.5 (.046) 

  Wind Survival: Mph (km/hr)................. 100 (160) 

 

PARTS LIST 

                                                    Note:  All hardware is Stainless Steel unless otherwise noted. 

 
Anti-Seize Compound

 

– Apply a small amount of the supplied Anti-Seize Compound to the aluminum joints and 

to the threads of the U-Bolts to prevent galling.

 

Содержание DSEDPM144-5LVA












Отзывы: