The
Dani Extreme V2
is an electronically controlled MOD that can be
used with various atomizers of different sizes and diameters. It is
offered in three different sizes and engineered to use one Li-Ion
battery of size 18350, 18500 or 18650.
The MOD is equipped with a graphical OLED display which provides status
information for 4 seconds after each vape.
Temperature controlled mode:
Battery
Always use batteries with high drain or very high current capability (even with
lower capacitance, except if power is below 20W). Avoid use no-name
products. Insert the battery with the plus terminal towards the atomizer.
Dani Extreme V2
The Extreme V2 is the next generation of the popular Dani Extreme. It
is equipped with an OLED display, has a power output of up to 40W
(up to 12V or 15A at the coil) and provides the option of temperature
controlled vaping with many different kinds of wire-materials—
dicodes-wire
, nickel, titan, appropriate stainless steel, and many
others. We recommend the
dicodes-wire
for optimal performance and
flavor experience.
Temperature at the end of vape
Other modes: battery symbol
Wattage setting
In Direct-Mode (Bypass)
it shows the actual power
applied to the coil.
Main Menu
If temperature
Battery-voltage at the end of
the vape, including voltage
drop during vape.
Coil-Resistance at end of vape,
including temperature dependent
increase.
Extended Functions Menu
Battery Status
Electronic cigarettes
Electronic cigarettes are NOT healthy, but studies indicate they are less
harmful than tobacco cigarettes.
Electronic cigarettes are an alternative to tobacco-products, but should not be
regarded as a dishabituation to smoking.
Electronic cigarettes are not intended for anyone under 18 years of age,
non-smokers, pregnant women, persons allergic to nicotine or propylene
glycol or persons with cardiovascular disease.
Selling to persons below 18 years of age is prohibited!
Battery Disposal
controlled vaping
is activated:
Temperature
Power
Up
(*1)
Heater Menu
Temp.-Coefficient
Mod-Menu
Battery Discharge
Value Menu
Number of
The Check Battery item shows the battery voltage with little current drained (Ub0)
and the battery voltage under load during the last puff (UbL). The difference
is the voltage drop of the battery. A high drop indicates a weak battery or contact
problems.
Li-Ion batteries may not be disposed in household waste. Customers are
required by law to dispose of worn out batteries at designated collection sites.
- 5 to 40W with one Li-Ion battery
Up
Power
Up
(*1)
Level
Puffs
short manual
-
Adjustabl
e battery
discharge
level 2.5-
3V
-
Up to 12V
output
voltage
-
Up to 15A
output
current
-
Temperatu
re
controlled
vaping
mode with
various
wire-types
-
Mechanic
al MOD
mode
(electroni
cally
overload
protected
)
-
10 Power
boost
modes
-
10 Heater
protectio
n modes
-
Atomizer
resistanc
e range
0.05 to 5
Ohms,
total
range
-
Atomiz
er
resista
nce
0.2-3.5
Ohms
(40W, guaranteed)
-
Reverse battery protection
-
Versatile menu structure
-
Individual user preferences selection
-
2 Year warranty on electronic
Temperature Down
Temperature Calibration
Coil Resistance Coil Temp.
(*1) not displayed in Bypass-Mode
(*2) with low (no) current (Ub0) and high current load (UbL)
Down
Coil Resistance
Check Battery (*2)
Heater Control
Switch Off Device
Enter Extended Functions Menu
01
dicodes Dani Extreme V2
03 Display Operation
06 Extended Functions Menu
05 Main Menu
Power Up and Power Down
Power Up increases the power to the Power-Limit value and then rolls over to 5W.
Power Down decreases the power down to 5W and then rolls over to the Power-Lim
value. The Power-Limit value is adjusted in the Extended Functions Sub-Menu “Heater”
and provides a protection feature for atomizers which are not prepared for high
wattage it also allows the user to reduce the power range intentionally.
Temperature Up and Temperature Down
This Menu item is
only displayed if temperature controlled vaping is selected
(see Heater-Control menu item below). The Temperature Up/Down menu sets the
setpoint for the coil temperature during vaping. The temperature setpoint can be
selected from 120°C to 280°C (250°F- 540°F) in steps of 5°C (10°F). To have high
precision temperature control, a correct reference measurement is mandatory.
Refer to manual for further details.
Manual Coil Temperature Calibration (*1)
Coil Resistance and Coil Temperature
The coil resistance is displayed in a range from 0.0 to 9.90 Ohms. If temperature
controlled vaping is selected, the current coil temperature is also displayed.
This Menu item is
only displayed if temperature controlled vaping is selected
(see Heater-Control menu item below). The Temperature calibration measures
the cold (20°C) coil resistance as the reference for temperature controlled vaping.
The calibration must be confirmed in a second step to avoid accidental activation.
02 Features
04 Menu Overview
