background image

Dedoes U.S. 

Headquarters

1060 W. West Maple Rd. 

Walled Lake, MI 48390

Support & Sales

248-624-7710

[email protected] 

www.dedoes.com

CSM15 - 2022

 

 

 

 

 

 

 

WIDTH: 

123 cm  / 48.5 in

HEIGHT: Varies

DEPTH: 

46 cm / 18 in

WEIGHT:  

Varies

ALLIANCE A1 

1.2M MACHINE

Alliance A1 Mix Machine 

Maintenance and Repair Guide

WWW.DEDOES.COM

Alliance A1 2.4M Machine 

· Serial number loca�on

· How to easily access the drive belts without  disassembly

· Belt installa�on

· Common replacement parts

· Lubrica�on

· Rou�ne maintenance

Maintenance and Repairs

Simple steps to correct common issues with the Alliance Machines

 

 

 

WIDTH: 

171 cm  / 67 in

HEIGHT: Varies

DEPTH: 

46 cm / 18 in

WEIGHT:  

Varies

ALLIANCE A1 

1.7M MACHINE

 

 

WIDTH: 

240 cm  / 95 in

HEIGHT: Varies

DEPTH: 

46 cm / 18 in

WEIGHT:  

Varies

ALLIANCE A1 

2.4M MACHINE

Alliance motors are ½ hp, single 
phase, 115 volt, 60 Hz with FLA of 

6.8 amps (782 Wa�s). 

Motors are explosion-proof, rated for 
Class 1, Division 1, Group D, 

hazardous loca�ons.

The motor is controlled by an 

intrinsically safe electronic �mer that 

operates on 5 volts DC.  

Both the motor and �mer are U.L and 

CSA approved.

Summary of Contents for Alliance A1 1.2M













Reviews: