background image

1

Beaulieu Vanity Unit, Mirror and Light

Thank you for purchasing this Croydex product.  Please follow the fixing and care instructions to 

ensure that your product is fitted safely and that it retains its high quality finish. Please retain this 

leaflet for future reference.

This instruction leaflet applies to the following products:

WC410122E BEAULIEU WHITE VANITY UNIT AND MIRROR SET

WC410176E BEAULIEU LIGHT OAK VANITY UNIT AND MIRROR SET

IMPORTANT INSTALLATION INFORMATION

               THIS IS A CLASS 2 APPLIANCE AND MUST NOT BE CONNECTED TO EARTH

INPUT: 220-240V ~ 200mA 4.8W IP 44

               HAZARDOUS VOLTAGES INSIDE  – DO NOT OPEN SEALED UNITS

THIS PRODUCT MUST BE CONNECTED TO A SWITCHED LIVE LIGHTING CIRCUIT

THERE ARE NO USER REPLACEABLE PARTS IN THE LIGHT UNIT

In accordance with Statutory Instrument 2004 No. 3210 - The Building (Amendment) (No.3) 

Regulations 2004, any work, other than repair/replacements, in a room where there is water (e.g. 

kitchen, bathroom, etc.) must be either:

• 

carried out by an electrician who is a member of a competent person self-certification 

scheme who will certify the work complies with the Building Regulations and you do not need to 

notify your local authority, or,

• 

carried out after prior notification to the Local Authority Building Control Department, which 

has responsibility for ensuring that the work is inspected and tested.

IMPORTANT WARRANTY INFORMATION

In accordance with Statutory Instrument 2004 No. 3210 - The Building (Amendment) (No.3) 

Regulations 2004, the installer must give the occupier of the premises in which this product has 

been installed a certificate to confirm that the requirements of regulations 4 and 7 have been 

satisfied, or the installation of this product must be inspected and tested by the Local Authority 

Building Control Department who will issue a compliance certificate.

A copy of this certificate may be required for certain warranty claims.  Failure to provide a copy of 

the certificate may invalidate the warranty.

This does not affect your statutory rights.

We recommend that you make yourself aware of the Regulations before you undertake any 

work and if you require clarification you should contact your Local Authority Building Control 

Department.

CAB 100 R01

Summary of Contents for Beaulieu Series








Reviews: