Cross Technologies 1582-650 Instruction Manual Download

Page: 1 / 11

Instruction Manual

Model 1582-650

RF Switch

January 2011 Rev C

STATUS

ALARM

HISTORY

RESET

ALARM

SWITCH

MANUAL

SELECT

CH1

AUTO

CH2

ONLINE

MANUAL REMOTE

SWITCH

RESET

CH1

ONLINE

MODEL 1582

SWITCH

POWER

ROSS

ECHNOLOGIES INC.

Data, drawings, and other material contained herein are proprietary to Cross Technologies, Inc.,

but may be reproduced or duplicated without the prior permission of Cross Technologies, Inc.

for purposes of operating the equipment. Printed in USA.

When ordering parts from Cross Technologies, Inc., be sure to include the equipment
model number, equipment serial number, and a description of the part.

ROSS

ECHNOLOGIES, INC.

6170 Shiloh Road

Alpharetta, Georgia 30005

(770) 886-8005

FAX (770) 886-7964

Toll Free 888-900-5588

WEB: www.crosstechnologies.com

E-MAIL: [email protected]

Summary of Contents for 1582-650












Search results

Summary of Contents for 1582-650

Reviews:

Related manuals for 1582-650

Brands by name

Popular brands

Cross Technologies 1582-650, Instruction Manual

Search results

Summary of Contents for 1582-650

Reviews:

Related manuals for 1582-650

Brands by name

Popular brands