ZUMMESH-KP
Zūm™ Wireless Keypad
Installation Guide
Description
The Crestron® ZUMMESH-KP provides control of one or more ZUMMESH-JBOX
load controllers (not included). It is available with either a single rocker switch or
four pushbuttons. The rocker switch version offers on/off switching and dimming
adjustment, with the ability to save one scene preset. The pushbutton version
supports on/off switching and dimming adjustment along with three scene presets.
Standard gang-box installation allows one or more units to be installed in a 3-1/2
inch (89 mm) deep electrical box. A finished installation requires a decorator-style
faceplate (not included).
Zūm Overview
A Zūm space consists of one space, such as a board room or conference room, that
is equipped with Zūm mesh devices. The Zūm mesh devices (i.e., dimmers, switches,
keypads, and sensors) in the space provide control and communicate directly with
each other without the need for a centralized gateway or processor.
To expand the functionality of the Zūm space, a ZUMMESH-NETBRIDGE (not
included) can be added which provides centralized control and monitoring from a
Crestron control system (not included).
NOTE:
The ZUMMESH-NETBRIDGE requires a compatible J-box device (not
included) to provide power.
Additional Resources
Visit the product page on the Crestron website
(
www.crestron.com
) for additional information and the latest
firmware updates. Use a QR reader application on your mobile
device to scan the QR image.
Important Notes
WARNING:
To avoid fire, shock, or death, turn off the power at the circuit breaker
or fuse and test that the power is off before wiring!
NOTE:
Observe the following points.
• Neutral: The ZUMMESH-KP requires a neutral connection to operate.
• Codes: Install in accordance with all local and national electrical codes.
• Installation: A qualified electrician should install this product.
• Wiring: Use copper wire only. For supply connections, use wire rated for at
least 75 °C.
• Temperature: For use where temperatures are between 32° to 104 °F
(0° to 40 °C).
• Electrical Boxes: Devices mount in standard electrical boxes. For easy
installation, Crestron recommends using 3-1/2 in (89 mm) deep electrical
boxes. Several devices can be installed in one electrical box (multigang). For
a smooth appearance, one-piece multigang faceplates (not included) can be
installed.
• Switches: Mechanical 3- or 4-way switches do not work with the
ZUMMESH-KP.
• Spacing: If mounting one device above another, leave at least 4-1/2 in (115
mm) vertical space between them.
Installation
To install the ZUMMESH-KP, do the following:
1. Turn the power off at the circuit breaker.
2. Wire the device as shown in the following diagram.
Neutral (white)
Hot (black)
Ground (bare or green)
100-277 VAC power
from breaker
3. Push all power wires back into the electrical box and fasten the device to the
electrical box with the provided screws.
4. Attach the decorative faceplate (not included).
5. Restore the power at the circuit breaker.
Multigang Installations
In multigang installations, several devices are grouped horizontally in one electrical box.
For a smooth appearance, install a one-piece multigang faceplate (not included).
NOTE:
When installing into a multigang box, do not fully tighten devices to the box
until the faceplate has been aligned.
NOTE:
Devices do not mount within a 2-gang mud ring. Use a standard 2-gang box.
Operation
Crestron offers the following ZUMMESH-KP units. Their functions are described below.
ZUMMESH-KP10A Operation
Press to set lights
to 90% (scene 1).
Press and hold to
raise the lights.
Press to turn the
lights off. Press and
hold to lower the
lights.
ZUMMESH-KP10B Operation
ON
SCENE 2
SCENE 3
OFF
Set loads to 90%. Press and hold to raise lights.
Turns loads off. Press and hold to lower lights.
Set loads to 50%. Press and hold 5 seconds to save preset.
Set loads to 10%. Press and hold 5 seconds to save preset.
How to Set Up a Zūm Space and Add Zūm Devices
Once all devices are physically installed in a board room or conference space, a new
Zūm space can be created and devices added.
NOTE:
Only set up one Zūm space at a time.
NOTE:
For simplified setup of a Zūm space, use the Zūm app on a mobile device.
Step 1
Create a New Zūm Space
Creating a Zūm space defines the area where the devices are located, such as a board
room or conference room. A Zūm space is created with a keypad, dimmer or switch, a
J-box device, or an AV Bridge.
NOTE:
Creating a Zūm space can only be performed by one device in the space.
NOTE:
A Zūm space cannot be created from a battery-powered keypad.
To create a new Zūm space using a keypad, dimmer, or switch:
1. Press the bottom button 5 times.
2. Press and hold the bottom button until the LED on the device lights (about
10 seconds). After approximately 3 seconds, the device LED begins slowly flashing.
This indicates that the Zūm space is now created and in Joining mode, allowing
you to add devices.
Press and hold until LED lights
Press 5x
then
To create a new Zūm space using a J-box device or an AV Bridge:
1. Press the
SETUP
button 5 times.
2. Press and hold the
SETUP
button until the LED on the device lights (about
10 seconds). After approximately 3 seconds, the device LED begins slowly flashing.
This indicates that the Zūm space is now created and in Joining mode, allowing
you to add devices.
TEST
SETUP
TEST
SETUP
Press and hold until LED lights
Press 5x
then
PWR
TX
RX
ERR
NET
SETUP
PWR
TX
RX
ERR
NET
SETUP
Press and hold until LED lights
Press 5x
then
NOTE:
The device that is used to create the Zūm space is automatically added to
the space and does not need to be added in Step 2.
Step 2
Add the ZUMMESH-KP to the Zūm Space
After a new Zūm space is created, add the ZUMMESH-KP while the space is in Joining
mode.
NOTE:
A Zūm mesh device can belong to only one space.
NOTE:
Joining mode ends automatically after 4 minutes.
To add the ZUMMESH-KP:
1. Press the top button 3 times.
2. Press and hold the top button until the LED on the ZUMMESH-KP lights (up to
10 seconds). The LED on the ZUMMESH-KP will start to flash slowly to indicate
that it has joined the space.
Press and hold until LED lights
Press 3x
then
Step 3
Complete Zūm Space Setup
To finish creating a Zūm space, press any button on a device that is part of the Zūm
space to exit Joining mode.
Add the ZUMMESH-KP to an Existing Zūm Space
Add the ZUMMESH-KP to an existing Zūm space by placing the Zūm space in Joining
mode.
Add the ZUMMESH-KP using a keypad, dimmer, or switch:
1. Enter Joining mode.
a. Press and hold both the top and bottom buttons until the LED lights (about
5 seconds).
b. Press the top button once.
c. Press the bottom button once. The LEDs on all devices in the space (except
battery powered devices) flash slowly to indicate that the devices are part of
the space and that the space is in Joining mode.
Press and hold until LED lights
Press and hold until LED lights
then
then
Press 1x
Press 1x
2. Add the ZUMMESH-KP.
a. Press the top button 3 times.
b. Press and hold the button until the LED on the ZUMMESH-KP lights (up to
10 seconds). The LED on the ZUMMESH-KP will start to flash slowly to
indicate that it has joined the space.
Press and hold until LED lights
Press 3x
then
3. Press any button on a device that is part of the Zūm space to exit Joining mode.
Add the ZUMMESH-KP using a J-box device:
1. Enter Joining mode.
a. Press the
SETUP
button 2 times.
b. Press the
TEST
button once. The LEDs on all devices in the space (except
battery powered devices) flash slowly to indicate that the devices are part of
the space and that the space is in Joining mode.
TEST
SETUP
TEST
SETUP
TEST
SETUP
Press SETUP 2x
Press TEST 1x
then
2. Add the ZUMMESH-KP.
a. Press the top button 3 times.
b. Press and hold the top button until the LED on the ZUMMESH-KP lights (up
to 10 seconds). The LED on the ZUMMESH-KP will start to flash slowly to
indicate that it has joined the space.
Press and hold until LED lights
Press 3x
then
3. Press any button on a device that is part of the Zūm space to exit Joining mode.
