P
LATINUM
S
ERIES
7500
K
EYPAD
I
NSTALLATION AND
P
ROGRAMMING
I
NSTRUCTIONS
Model 7520
(Front)
Model 7530
(Side)
P
ROGRAMMING
Q
UICK
G
UIDE
Enter Programming Mode
** (master code) **
Example:
** 1234 **
Programming Functions:
Set Relay to M omentary
1 (time in seconds) #
Example:
1 05 # (Sets to 5 secs)
Set Relay to Latch
1 00 #
Add New User
2 (user n umber) # (user
code) # (user code) #
Example:
2 002 # 22222 # 22222 #
Change Existing User
2 (user n umber) # (user
code) # (user code) #
Example:
2 002 # 23456 # 23456 #
Change Master Code
2 0 # (new master code) #
(new master code) #
Example:
2 0 # 382436 # 382436 #
Erase a User Code
3 (user code) #
Example:
3 23456 #
Erase All Users
4 (master code) #
Example:
4 382436 #
Note:
New Master Code must be between 4 & 8 digits.
Option 4 erases all User Codes, but not the
Master C ode.
A
VAILABLE
M
ODELS
Model 7510
(Front)
S
PECIFICATIONS
%¸
Input Voltage:
12-24 Volt DC or 12 Volt AC
%¸
Power Consumption:
120mA max @ 24 VDC, 20mA idle
NOTE:
3A Power Supply is recommended for use with
door strike or magnetic lock
%¸
Programmable Relay:
Form C, dry contacts
rated at 2A @ 30VDC (inductive load)
%¸
Operating Temperature:
-40
o
C to 125
o
C (-40
o
F to 257
o
F)
%¸
Available Models w ith Inst alled Dim ensions:
%¸
7510:
Single-Gang Style Keypad
3.20" W X 5.10" H x 0.75" D
%¸
7520:
Mullion Surface-Mount Keypad
1.75" W X 7.125" H x 1.00" D
%¸
7530:
Mullion Mortise-Mount Keypad
1.75" W X 7.125" H x 0.25" D
%¸
User Codes:
Up to 200 unique codes including
1 master code. Codes will be between 4 and 8
digi ts in lengt h. Cod es are st ored in nonv olat ile
EEPROM memory.
%¸
Lockout Feature:
Keypad will lock out all
funct ions for 30 second s aft er thr ee consec utiv e
invalid codes.
%¸
Factor y Defa ult Sett ings:
%¸
Master code
1 2 3 4
%¸
User code
5 6 7 8 9 0
%¸
Relay Time 5 seconds (Momentary)
P
HYSICAL
D
ESCRIPTIONS
LED Explanation:
%¸
Green LED
:
%¸
Steady off = D oor rel ay deac tiva ted
%¸
Steady on = Doo r rela y acti vated
%¸
Red LED:
%¸
Normal Operation:
i)
Three sec onds o n = Inv alid code
entered.
ii)
Slow flash = 30 second delay due to
three consecutive invalid codes entered.
%¸
Progr amm ing Mo de:
i)
Slow flash = Program standby, ready to
accept new function.
ii)
Fast flash = Program in progress,
awaiting input.
iii)
Very fast flash = Erasing all user codes.
Wire Connections:
%¸
Power
- Connect either a 12 - 24 volt direct
current (DC) or a 12 volt al ternating current (AC)
power supply to these terminals. Polarity does not
matter, as the keypad has been designed to work in
both directions. Power supplies outside this range
may cause permanent damage to the keypad.
%¸
Common
- This terminal is the Common output
of the relay and is used in conjunction with the
N.O. or N.C. Terminals (see below) to control a
door lock.
%¸
N.O.
- This term inal is th e Norm ally Open
outpu t of t he relay . In a n orm al lo cked st ate,
this terminal is disconnected from the Common
terminal. In an unlocked state, this terminal is
connected to the Common terminal.
%¸
N.C.
- This term inal is th e Norm ally Closed
outpu t of t he relay . In a n orm al lo cked st ate,
this terminal is connected to the Common
terminal. In an unlocked state, this terminal
disconnects from the Common terminal.
%¸
Reset Button
- This button is used to reset the
master code back to its factory default. Follow
the in stru ctio ns out lined in the
Programming
section, under
Factory Reset Function
.
