Chamberlain HCTDCU Installation Manual Download

Page: 1 / 12

COMMERCIAL 24VDC HIGH TRAFFIC

OVERHEAD DOOR AND GATE OPERATOR

WITH BATTERY BACKUP

Model

HCTDCU

INSTALLATION MANUAL

LiftMaster
845 Larch Avenue
Elmhurst, IL 60126-1196

•

THIS PRODUCT IS TO BE INSTALLED AND SERVICED BY A
TRAINED TECHNICIAN ONLY.

•

This model is for use on vehicular passage gates or
commercial doors ONLY and not intended for use on
pedestrian passage gates.

•

Install the operator at least 8 feet (2.4 m) above the floor.

•

This model is intended for use in Class II, III and IV vehicular
trolley gate or commercial door applications.

•

Visit LiftMaster.com to locate a professional installing dealer
in your area.

•

This gate/door operator is compatible with MyQ

and

S 2.0

accessories.

Take a photo of the camera icon

including the points ( ).

Send it in by texting the photo to 71403

(US) or visit www.liftmaster.photo

(Global)

HCTDCU

Motor Unit

HCT08

8 Foot Rail

HCT10

10 Foot Rail

HCT12

12 Foot Rail

PHOTOREGISTER

LM-HCTROLLEY

Summary of Contents for HCTDCU













Search results

Summary of Contents for HCTDCU

Reviews:

Related manuals for HCTDCU

Brands by name

Popular brands

Chamberlain HCTDCU, Installation Manual

Search results

Summary of Contents for HCTDCU

Reviews:

Related manuals for HCTDCU

Brands by name

Popular brands