SAFETY PRECAUTIONS
This machine is intended for commercial use only. It is designed
to be operated by trained and qualified operators only. It is to
only be operated in the manner indented - to scrub, polish,
clean, and restore hard surface flooring, in an indoor environ-
ment. Use only recommended pads/brushes, commercially avail-
able floor cleaners and waxes with this machine.
All Operators must read, understand and practice the following
safety precautions.
WARNING: Fire or Explosion Hazzard
Never operate the machine in or near flammable liquids, vapors or
combustible dusts. This machine is not equipped with an explosion
proof motor. Under normal operation, the electric motor will spark
upon start up and during operation which could cause a flash fire
or explosion if the machine is used in an area where flammable
vapors/liquids or combustible dusts are present.
WARNING: Electrical Hazard.
Do not operate the machine with a damaged power cord. Do not
modify the plug. Unplug the power cord before servicing the ma-
chine. A damaged or broken power cord must be replaced by the
manufacturer or its service agent or a similarly qualified technician
to avoid a hazard.
WARNING: Electrical Shock Hazard.
Do not use outdoors. Do not expose to rain. Store indoors in a dry
environment.
The following checklists provide critical information to the opera-
tor of the equipment and must be considered each time the ma-
chine is to be operated:
FOR SAFETY:
Do
NOT
operate the machine:
Near or on flammable liquids or vapors as an explosion or flash
fire may occur
Unless you have been trained on the use of this equipment and
are authorized to do so
If you have not read and understood the Operator’s Manual
Unless the power cord is properly grounded
With a damaged power cord or plug
If the machine is not in proper operating condition
In outdoor areas
In standing water
With the use of an extension cord
In areas that have not been cordoned off
BEFORE STARTING MACHINE:
Make sure all safety devices are in place and operate properly
Remove loose objects from the floor to prevent accidental dam-
age from loose objects being struck by spinning pad and be-
coming dangerous projectiles.
Place wet floor signs as needed and ensure that there is no pe-
destrian traffic near the machine when it is being used
WHEN USING THIS MACHINE:
Stay clear of spinning pad
Do not pull machine by plug or power cord
Do not run machine over cord
Do not pull cord around sharp edges or corners
Do not close doors on cord
Do not unplug by pulling on cord
Do not stretch cord
Do not handle plug with wet hands
Keep cord away from heated surfaces
Follow mixing and handling instructions of chemical containers
Never activate the power when the handle is in the upright posi-
tion.
Do not release handle grips until pad comes to a complete stop
Go slow on inclines and slippery surfaces
Wear non-slip, steel toe safety boots
Report machine damage or faulty operation immediately
Never allow children to play on or around the machine
Never use “aftermarket” parts or cables
Never leave the machine unattended and plugged in
BEFORE LEAVING OR SERVICING MACHINE:
Turn off machine
Unplug cord from wall outlet
SERVICING THIS MACHINE:
The machine should only be serviced by trained and qualified tech-
nicians
Only use manufacturer supplied replacement parts
All repairs must be performed by a qualified service person
Do not modify the machine from its original design
Contact Centaur Floor Machines to locate service centers
WHEN TRANSPORTING THIS MACHINE:
Get assistance when lifting machine.
Unplug cord from wall outlet
Wind cord safely to avoid tripping hazard
Use tie-down straps to secure machine to truck or trailer
Ensure machine is kept +5c Temperature or higher at all times
GROUNDING INSTRUCTIONS:
This machine must be grounded when being used in order to reduce
the risk of electrical shock. The plug must be plugged into an appropri-
ate outlet that is properly installed in accordance with all local codes
and regulations. Do not remove ground pin. If missing, replace plug
before use.
This machine is for use on a nominal
120-Volt circuit and has a grounding
attachment plug that looks like the
plug illustrated. Make sure that the
machine is connected to an outlet
having the same configuration as the
plug. No adaptor should be used with
this machine.
