![background image](http://html1.mh-extra.com/html/cable-tronix/ct-hdvd-hdcx-ir/ct-hdvd-hdcx-ir_user-manual_3187862001.webp)
User Manual
HDMI RF Extender over Coaxial
Cable with IR
1
Introduction
HDMI to RF sender TX*1pcs
User's manual 1pcs
1.HDMI source device(computer graphics card, DVD,PS3, HD monitor
equipment etc).
2.SDTV, HDTV or projector with HDMI port.
3.RG6(
) or upper level coaxial cables.
RF to HDMI receiver RX*1pcs
1. HDMI to RF sender TX
RF RX: RF signal receive interface
IR IN: IR receiver extension cable interface
DC5V: DC 5V power input
LINK: signal connection led
indicator
2
Features
Remote control
HDMI OUTPUT: HDMI output
6
Connection
DC5V1A*2pcs
2.RF to HDMI receiver RX
4. IR remote control
RF TX: RF signal send interface
RESET: Press to reset
DC5V: DC 5V power input
IR IN: IR receiver extension
cable interface
HDMI INPUT: HDMI signal input
1
2
3
4
5
1
2
3
4
5
1
2
3
5
4
1
2
3
4
5
6.1 One-to-one connection
6.2 One-to-many conection
:
Connect one CATV splitter to utilize
splitter function.
6.3 Many to many connection
:
Connect two CATV splitters to build
video matrix.
Note: for above“CATV
splitter 1”, it needs to use“OUT”as the signal
input and“IN”as signal output.
For“CATV splitter 2”, just follow the marks on the panel description.
DVD
TV
TX
RX
DVD
TV
TX
OUT
4 WAY SPLIT TER 5-1000MHz
HIGH ISOL ATION&SCREENING
SB-408E
OUT
OUT
OUT
IN
RX
RX
RX
TV
TV
DVD
TX
OUT
4 WAY SPLIT TER 5-1000MHz
HIGH ISOL ATION&SCREENING
SB-408E
OUT
OUT
OUT
IN
TV
RX
RX
RX
TV
TV
TX
TX
OUT
4 WAY SPLIT TER 5-1000MHz
HIGH ISOL ATION&SCREENING
SB-408E
OUT
OUT
OUT
IN
DVD
DVD
Q. It shows “NO SIGNAL” on screen.
A
:
1) Make sure to set TV source signal to the correct channel.
2) If link LED
is not on, check if TX and RX channel settings are
the same.
3) If coaxial cable is too long, please refer to Appendix 1 to adjust
channel setting.
7
FAQ
Q. Image is not normal after setting channel (splash screen, disturbance,
mosaic etc)?
A
:
Make sure coaxial cable connection is stable. Try a different channel or
power-cycle the TX unit.
Q
:
There is video image output but no sound?
A
:
Power-cycle the TX unit by disconnecting power for 20 seconds and
reconnect power.
OUT
4 WAY SPLITTER 5-1000MHz
HIGH ISOLATION&SCREENING
SB-408E
OUT
OUT
OUT
IN
6.4 Other notes
Important safety notice
1. Please pay attention to all the warnings and hints on this device.
2. Do not expose this unit to rain, moisture or liquid.
3. Do not put anything on top of the device.
4. Do not repair or open this device without professional
guidance.
5.
Ensure good ventilation to avoid product overheating .
6. Shut off power and make sure the area is safe before installation.
7. Do not connect the network cables and IR cables when the device is on,
to avoid damage.
8. Use DC5V only. Make sure the specification matches if using 3 party
DC adapters.
rd
Please read below safety instructions carefully before installation and operation:
1) Fully compatible with HDCP.
2) Transmit up to 700meters with RG6( 75
Ω
) at 1080P@60Hz.
3) Support up to 100 channels.
4) Support CATV splitter and amplifier connection.
5) High quality image, long distance transmission and strong
anti-interference ability.
6) Supports IR remote switching at the receiver.
3
PACKAGE CONTENTS
4
INSTALLATION REQUIREMENTS
5
Panel description
3. Channel parameters settings
Channel setting buttons
1
2
1
2
Channel display screen
CATV splitter
CATV splitter 1
CATV splitter 2
IR receiver extension
cable x1pcs
CT-HDVD-HDCX-IR
This HDMI over RF extender utilizes RF conversion technology to convert an
HDMI signal to an HD digital TV signal, and transmits it by coaxial cable up
to 700 meters. It provides a high quality image and anti-interference
capability and can be used with a CATV splitter to realize one to many, many
to many, and video matrix operations.
The HDMI extender can be applied to a wide variety of operations, such as
CCTV monitoring, large outdoor screens, shopping malls, education, digital
KVM fields, etc.
1. Cable length is suggested to be between 300 & 700 meters. If the cable
is shorter than 100 meters, a signal attenuator of at least 20db will be
needed. Choose an attenuator size which provides proper signal level at the
TV.
2. Refer to appendix 1 for channel-frequency mapping table; refer to
appendix 2 for coaxial cable signal loss values for each channel frequency.
3. When using a CATV splitter for 1-to-many and many-to-many operation,
please use a bi-directional splitter with low insertion loss, high shielding and
a frequency range of at least 5 ~ 1000Mhz
The IR remote is used solely to change the receive channel of the RX
device at the TV. For example, if there is a Playstation on channel 1, a
Blu-Ray player on ch 2 and a Satellite receiver on channel 3, use the
remote to choose ch1 to see the playstation, ch2 for the Blu-Ray etc.
*This channel selction is for the receivers only, and is not passed across the
coax to the transmitter(s).
75
Ω
There are 100 channels (0~99), selected with 2 buttons. The left
button changes the‘singles’digit (on the right) and the right
button changes the “tens”digit (on the left). For eaxample, to set
channel “21”, press the right button until the left digit is “2” and
press the left button until the right digit is “1”. Connection
between a TX device and an RX device is only possible when both
devices are set to the same channel.