Bryant TSTATBBP071-01, Installation, Start-Up And Service Instructions Manual

Page: 1 / 8

CONTENTS
Page
SAFETY CONSIDERATIONS . . . . . . . . . . . . . . . . . . . . . . 1
GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
I. Select Thermostat Location . . . . . . . . . . . . . . . . 1
II. Install Thermostat . . . . . . . . . . . . . . . . . . . . . . . . 2
III. Heat Pump Configuration . . . . . . . . . . . . . . . . . . 2
IV. Configure Advanced Setup . . . . . . . . . . . . . . . . . 2
V. Install Accessories . . . . . . . . . . . . . . . . . . . . . . . . 4
VI. Sensor Calibration
. . . . . . . . . . . . . . . . . . . . . . . . . 5
VII. Check Thermostat Operation . . . . . . . . . . . . . . . . 5
VIII. Final Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
I. Mode Button Operation . . . . . . . . . . . . . . . . . . . . 6
II. Fan Button
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
III. Emergency Heat Button . . . . . . . . . . . . . . . . . . . . 6
IV. Backlight Button . . . . . . . . . . . . . . . . . . . . . . . . . . 6
V. Reset Filter Button . . . . . . . . . . . . . . . . . . . . . . . . . 6
VI. Override Button
. . . . . . . . . . . . . . . . . . . . . . . . . . 6
VII. Electric Heat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
VIII. Two-Stage Operation . . . . . . . . . . . . . . . . . . . . . . 6
IX. Remote Temperature Sensor . . . . . . . . . . . . . . . . 6
X. Keypad Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
XI. Dry Contact Switch/External Control . . . . . . . . . 6
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
IMPORTANT: Read entire instructions before starting the
installation.
SAFETY CONSIDERATIONS
Read and follow manufacturer instructions carefully. Follow
all local electrical codes during installation. All wiring must
conform to local and national electrical codes. Improper wir-
ing or installation may damage thermostat.
Recognize safety information. This is the safety alert symbol
. When the safety alert symbol is present on equipment or
in the instruction manual, be alert to the potential for per-
sonal injury.
Understand the signal words DANGER, WARNING, and CAU-
TION. These words are used with the safety alert sym-
bol. DANGER identifies the most serious hazards which will
result in severe personal injury or death. WARNING signi-
fies a hazard which could result in personal injury or death.
CAUTION is used to identify unsafe practices which would
result in minor personal injury or property damage.
GENERAL
The commercial, programmable thermostats are wall-mounted,
low-voltage thermostats which maintain room temperature
by controlling the operation of an HVAC (heating, ventila-
tion, and air-conditioning) system. Separate heating and cool-
ing set points and auto-changeover capability allow flexibil-
ity. Dry contacts are available to control the thermostat to
occupied and unoccupied set points from an external device
for energy savings.
Batteries are not required. During power interruption the
internal NEVERLOST™ memory stores the thermostat con-
figuration for an unlimited time.
The thermostat can be configured to accept several different
equipment configurations, including heat pump operation.
NOTE:
The thermostat is not factory-configured for use in
heat pump applications. The advanced setup must be per-
formed to configure the thermostat for use with heat pump
units.
INSTALLATION
I. SELECT THERMOSTAT LOCATION
The thermostat should be mounted:
• approximately 5 ft from the floor
• close to or in a frequently used room, preferably on an in-
side partitioning wall
• on a section of wall without pipes or ductwork
• where temperature operating limits are within 41 to 104 F
(5 to 40 C)
• where humidity operating range is within 0 to 95% rela-
tive humidity, non-condensing
The thermostat should NOT be mounted:
• close to a window, on an outside wall, or next to a door
leading to the outside
• where exposed to direct light and heat from a lamp, the
sun, a fireplace, or any other temperature-radiating object
which may cause a false reading
• close to or in direct airflow from supply registers or return
air grilles
• in areas with poor air circulation (such as behind a door or
in an alcove)
installation, start-up and
service instructions
TEMPSURE COMMERCIAL THERMOSTAT —
PROGRAMMABLE
(P/N TSTATBBP071-01)
Cancels: New II TSTAT-6
11/1/98