1-1/4"
32mm
1-1/2"
40mm
1/4"
6mm
Activation
Area
SureFlo
®
Automatic, 1" Counter-Mounted Soap Dispenser
INSTRUCTIONS FOR INSTALLATION, OPERATION & MAINTENANCE
BOBRICK MODEL B-8281 FOAM SOAP DISPENSER
Parts List:
Item Description
1
Top Assembly with Spout, Door and Stem
2
LED Light Pipe
3
Foam Nozzle Tip with Mesh
4
Fiber Optic Insert with Sensor Lenses
5
Rubber Counter Gasket
6
Wave Washer
7
Mounting Nut
8
Stem Locking Nut
9
Foam Mixer Housing
10
Bottom Housing Assembly (includes Soap
Bottle)
11
Air Tube
12
Air Tube Adapter
13
(3) Fiber Optic Cables for Sensor and LED
Light Pipe
14
Fiber Optic Connector Tip Assembly
15
Fiber Optic Nut
16
Automatic System Flush Button
17
Portion Control Knob
18 BobKey
19
Key Hole
20
Battery Pack (requires (4) “D” cell alkaline
batteries not included).
21
Optional: A/C Adapter Kit with U.S. Plug, order
Part No. 3974-57
For outlets not compatible with U.S. plugs,
order Part No. 3974-55
© 2021 by Bobrick Washroom Equipment, Inc.
Form
No.
8281-91
r4/22/21 Printed
in
U.S.A.
Clearances and Mounting Requirements:
• Minimum 1" (25.4mm) diameter mounting hole required.
• Minimum 18" (457mm) vertical clearance needed below the counter.
• 5" (127mm) diameter clearance needed below the mounting hole to accommodate
bottle and bottom housing.
• Minimum 2-1/4" (57mm) diameter clearance needed for Mounting nut directly below
the counter to clear sink rim.
• Recommend drilling mounting hole 6" to 8" (150 to 205mm) from the wall, and 2-1/2" to
3" (65 to 75mm) from sink rim.
Routine Cleaning and Maintenance:
Using a damp cloth, wipe the chrome-plated exterior of the dispenser daily. Periodically (about 3 to 6 months), it is
recommended to flush the system with lukewarm water for cleaning and maintenance.
1. When minimal amount of soap is left in the bottle, fill dispenser with lukewarm water from
top to dilute soap.
2. Press on Automatic System Flush Button to flush the system.
3. Once unit is flushed, press Automatic System Flush Button again to stop dispensing.
4. Fill unit with fresh foam soap, and dispense as usual.
For Retrofit:
1. Remove existing dispenser(s).
2. Clean area.
3. Ensure hole is 1" (25.4mm) diameter.
4. If necessary, enlarge opening using appropriate hole saw. For granite/marble counters, recommend using a diamond hole saw
(consult with stone and granite specialist). If needed, mounting hole should be offset to clear the sink rim. The Mounting nut
requires 2-1/4" (57mm) diameter clearance directly below the counter.
To Operate:
Troubleshooting:
1. Soap dispenser does not dispense soap, but you can hear motor running. The green LED lights up when hands are under spout.
a. Press the Automatic System Flush Button until soap comes out
b. Press Automatic System Flush Button again to turn it off
2. Soap dispenser does not dispense soap and you cannot hear motor running. The green LED does not light up when hands are
under spout.
a. Be sure power is supplied to unit.
b. Make sure Fiber Optic Nut is threaded hand-snug onto Fiber Optic Port.
Warranty:
SureFlo Automatic Foam Soap Dispenser is warranted to be free from defects in workmanship and material under normal
usage from the date of purchase for a period of 3 years.
For New Installation:
• Refer to mounting template for drilling locations (Form No. 8281-7).
1.
Prime Unit –
After filling
dispenser, plug in power
to start prime. If unit is
plugged in prior to filling
dispenser, place hand
under spout within sensor
location to start prime.
2.
Standard Dispense –
Place hand under spout
within the sensor location
for approximately 1/2
second to dispense
controlled amount of
foam hand soap.
3.
Adjusting the foam quality –
Foam quality in terms of
more or less liquid used to
produce the foam can be
adjusted by rotating the
Portion Control Knob
clockwise for more air in the
foam and counterclockwise
for less air in the foam.
4.
LED Light Indicators –
When activated, solid
green LED will light.
If green light is flashing,
remove hand to allow
unit to reset, then activate
again. If using battery
pack, flashing red LED
light indicates time to
replace batteries.
In the U.S.A.: BOBRICK WASHROOM EQUIPMENT, INC.
Los Angeles: 6901 Tujunga Ave., North Hollywood, CA 91605-6213: Tel: (818) 982-9600, FAX: (818) 503-1102
New York: 200 Commerce Drive, Clifton Park, NY 12065-1350; Tel: (518) 877-7444, FAX: (518) 877-5029,
or e-mail: [email protected]
In Canada: BOBRICK WASHROOM EQUIPMENT COMPANY
45 Rolark Drive, Scarborough, Ontario M1R 3B1 • Eastern Canada: Tel: (877) 423-6555 • FAX: (877) 423-8555
• Western Canada: Tel: (877) 423-6444 • FAX: (877) 423-8444
BOBRICK.COM
Scan for SureFlo Automatic 1" Foam
Soap Dispenser Installation Video.
1
4
