Black & Decker Workmate 79-020 Owner'S Manual Download

Page: 1 / 8

METAL VISE

JAW COVERS

SWIVEL GRIPS

(4)

V-GROOVES

WING SCREWS (2)

(FOR TILT)

Black s Decker ,

WORKMATE®

Bench Top Work Center and Vise

Tilt Top 16" Model 79-020

-DOUBLE VISE JAWS

BENCH CLAMPS

VISE HANDLES (2)

• Can b e mounted with included clamps o n any work surface u p t o 21/2" thick.

Suction cups on bottom provide added stability and minimize marring of the work

surface.

• 1 6 " Vise Jaws open up to 51/4" wide. Included Metal Vise Jaw Covers can be used

to protect the vise jaws when gripping objects with shapes o r edges that could
damage the jaws.

• Swivel Grips hold irregular shapes and lumber u p t o 121/2" wide, u p t o 1 4 "

diagonally.

• Surface can be tilted to 15°, 30° or 45° for use in craft or hobby work.

• V -grooves in vise jaws hold pipe or tubing in horizontal or vertical positions.

• Can be hung on wall or stored under workbench when not in use.

Please read this manual carefully so that you can take full advantage of the versatility

of the WORKMATE®.

OWNER'S MANUAL

Summary of Contents for Workmate 79-020









Search results

Summary of Contents for Workmate 79-020

Reviews:

Related manuals for Workmate 79-020

Brands by name

Popular brands

Black & Decker Workmate 79-020, Owner'S Manual

Search results

Summary of Contents for Workmate 79-020

Reviews:

Related manuals for Workmate 79-020

Brands by name

Popular brands