BIS PANORAMA Installation And Operating Instructions Manual Download | Manualshive

Page: 1 / 47

background image

Installation and Operating

Instructions

This  installation  manual  will  help  you
obtain  a  safe,  efficient,  dependable
installation  for  your  fireplace  and
chimney  system.  Please  read  and
understand  these  installation  instructions
before beginning your installation.

CAUTION:    Do  not  attempt  to  modify
or  alter  the  construction  of  the  fireplace
or  its  components.  Any  modification  or
alteration  of  construction  may  void  the
warranty,  listings  and  approvals  of  this
system.  In  that  case,  Security  Chimneys
International  Ltd  will  not  be  responsible
for damages.  Install the fireplace only  as
described in these instructions.

PLEASE RETAIN THIS MANUAL

FOR FUTURE REFERENCE

WARNING: The fireplace cannot be
operated without a door. Consult your
dealer to select the correct door model.

2125 Monterey St., Laval, Quebec, Canada, H7L 3T6

Printed in Canada

Rev. 8 Oct 2006 PIBISPANO

•

Hot! Do not touch!

The glass

and  surfaces  of  this  appliance
will be hot  during  operation  and
will retain  heat  for  a  while  after
shutting off the appliance. Severe
burn may result.

•

Carefully supervise children in

the same room as appliance.

•

If small children are present in the home, it
is recommended that this appliance be used
with a fire screen kit.

Listed to standards:
ULC-S610, UL-127
Report # 192-5237

1
2
3
...
»

Summary of Contents for PANORAMA
















































Reviews:

No comments

Related manuals for PANORAMA

Brand: IHP Pages: 8

Brand: Valor Fires Pages: 8

LUNA 850 V Gold Gas

Brand: M Design Pages: 39

Brand: Home Decorators Collection Pages: 16

Brand: Bluegrass Living Pages: 30

Brand: Vexar Pages: 36

Brand: Valor Pages: 12

Brand: Sunnydaze Decor Pages: 2

Brand: Everwarm Pages: 25

Brand: ClassicFlame Pages: 18

Brand: baltur Pages: 88

Regency OXYSAFE 2

Brand: Valor Pages: 22

ZERO CLEARANCE ZC Series

Brand: DON-BAR Pages: 26

Brand: Bio-Blaze Pages: 16

Brand: kozy heat Pages: 51

Leveling Leg Field Fix Kit MPE-27

Brand: Lennox Hearth Products Pages: 1

Brand: Valcourt Pages: 6

ChimneyFree 1142880

Brand: Twin-Star International Pages: 50

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands