Welcome Guide
Wireless controller
HS03-1
Specifications
1.Transmission Media: Bluetooth 2.1
2.Carrier Wave: 2.402-2.480GHz
3.Protocol: Bluetooth 2.1
4.LED: 8 LED Lights & 8 Multi-Color LED lights
5.Battery: One Lithium polymer battery、3.7V 400/mAH
6.Battery life: 2-3 hours after fully charged
7.operating voltage: 3.7V-4.2V
8.charging voltage: 5V
9.Operating temperature: -10℃~50℃
10.storage temperature: -20℃~70℃
11.Dimensions (approx): 7*20*41mm
12.weight(approx): 149g
Connection
A.Conventional Connection
1.Attaching the controllers to the console will connect them
automatically.
2.The Joy-Con controllers will remain paired when you detach
them from the console, and you'll be able to use them wirelessly.
Button Layout
Turbo Function
Note:
The T button on the left controller can only the assign the
buttons that are on the left controller. Same goes for the T button
on the right controller.
Turbo Mode
A: Hold down the T button and then press the button that you
want to set for the 1st time to turn on the normal turbo function.
(Controller will vibrate.)
B: Hold down the T button and then press the button that you
want to set for the 2nd time to turn on the automatic turbo
function. (Controller will vibrate.)
B：Bluetooth Reconnecting
Press the Home button or the Capture button to reconnect your
controllers back to the console, 4 LED indicators on the side will
start to flash in a regular pattern as an indication of reconnecting.
Turn Off
Hold down the T button and then press the button that you
have set for the 3rd time to turn off its turbo function. (Controller
will vibrate.)
* Hold the T button for 5 seconds to cancel the Turbo function of
all buttons.
Turbo Speed Adjustment
* A total of 3 turbo speeds can be adjusted cyclically.
Hold down the T button and press the ‒ button for Controller(L).
(Controller will vibrate.)
Hold down the T button and press the + button for Controller(R).
(Controller will vibrate.)
Buttons can be set
Left controller： L / ZL button and Control Pad (Up / Down/ Left/
Right).
Right controller： R / ZR button and A / B / X / Y button.
Vibration Level Adjustment
Press the T button and push the Joy-stick up or down to adjust
the vibration level of each controller.
(Controller will vibrate when adjusting between each vibration
level.)
[2]
[3]
[4]
[1]
[6]
[7]
[8]
1. - button
2. Left stick
3. Directional pad
4.Turbo button
5. Screenshot button
6. +button
7. X button
8. A button
9. Y button
10. B button
11. Right stick
12. Home button
13.Turbo button
14. L button
15. ZL button
16. SL button
17. Pairing button
18. SR button
19. Type-C interface
20. ZR button
21. R button
22. SR button
23. Pairing button
24. SL button
25. Type-C interface
1
2
* There are 5 levels of Vibration：100%，75%，50% ，30%，0%.
(Default level is 50%)
LED Ring Setting
A: Normal Mode
Hold the T button and press the joystick once to turn the light
into normal mode（the light will keep on this color），and repeat
this procedure to change color.（Controller will vibrate when set
successfully)
1-8 colors: 1.Red 2.Orange 3.Yellow 4.Green 5.Cyan 6.Blue
7.Purple 8.Rainbow
Brightness Adjustment
Press & hold the T button and joystick to change the brightness,
then release the joystick to fix the brightness. （Controller will
vibrate when set successfully)
B: Breathing Light Mode
Hold the T button and press the joystick twice to turn the light
into breathing light mode, the following three modes will be
cycled.
（Controller will vibrate when set successfully)
Mode 1: 1-7 color auto cycling.
Mode 2： Rainbow light.
Mode 3: Light off.
Gyro Calibration
1. First, press and hold the Pairing Button to turn off the
controller.
2. For controller(L), press the L , UP and the Capture button
together to enter the calibration mode.
For controller(R), press the R , X and the Home button together to
enter the calibration mode.
3. When entering the calibration mode, LED lights will flash
alternately. Then align the controllers with the rails on either side
of the console, and slide them down BUT DO NOT slide them to
the bottom of the rail. (If you hear a click you need to press the
release button and slide them up a little.)
4. Then press the - button for controller(L) and + button for the
control(R) to start the calibrating. Controllers will be reconnected
back to the console when calibration is over.
2
1
Charging Instructions
1.When the controllers are in the USB charging state, LED lights will
flash slowly, if connected to the console, the lights will stay on
when it is fully charged; If not, the light will be off.
2.When the pairing indication conflicts with the charging low
power indicator, the pairing indicates a concern.
Warning
1. Do not expose the controller to high temperature, high humidity
or direct sunshine.
2. Do not allow liquid or small particles to enter the controller.
3. Do not put any heavy object on the controller.
4. Do not disassemble the controller.
5. Do not twist or pull the cable too strongly.
6. Do not throw, drop, or apply strong shock to the controller.
[5]
Driver Package
We support downloading the driver package through a USB
connection to the computer to fix some problems that may be
encountered in use. If the driver package does not work, please
contact us by email ([email protected]).
Driver package download website: www.binbok.com
Note：
No need to download driver if it can be used normally,
otherwise new problems may occur due to version conflicts)
Use Method
1.Turn off your controllers.
2.Press down and hold the Left(Right) stick then connect them to
your computer and release.
3.Run the Driver package.
4.Click the Update Firmware on your computer.
Low Voltage Alarm
1. If the lithium battery voltage is lower than 3.45V±0.1V, the
current channel tight flashes quickly and indicate low voltage.
2. If the lithium battery voltage is lower than 3.35V±0.1V, it will
automatically sleep.
9
10
11
12
5
14 15
20 21
7
6
1
2
3
4
16
17
18
19
22
23
24
25
SL
SR
13
8
SL
SR
3
4
Reset Button Function
When there are some unsolvable faults in the controller, you can
try to press and hold the reset button on the back of the
controller for more than 5 seconds. At this time, the controller is
powered off and reset, and you need to reconnect according to
the method of connecting the controller for the first time.
Binbok Game
Business Contact: [email protected]
@BINBOKOffcial
EUR: [email protected]
Official Homepage : binbok.com
（Register on this web to activate aftersales.）
