background image

Delete This Page before printing!! 

 

To Keep Page Orientation Correct 

 
 

Instructions for Printing & Binding 

 
 

This page gets wasted, to maintain orientation of pages throughout the manual when viewing 
online, To allow viewing 2 Pages Up. 
 
 Begin printing on Page 1 (the Cover) and print both sides of paper. 
 
Page orientation is important.  This can be seen when you get to Pages 22 & 23 which should be 
facing you when the Manual is open, as well as many more as you progress through the manual. 
This has the Narrative and the proper Drawing facing you at the same time. 
 
Print on 20 Lb (Min.) Premium Paper or better, Printing both sides of paper. 
 
I prefer Spiral Bound with Clear Front Cover and Heavy Black Back Cover. 
This allows the manual to be opened and folded back leaving the desired page exposed and lays 
flat when opened to expose 2 pages while doing Inspections or Maintenance. 
 
I generally get them printed at Staples or Office Depot where it costs as little as $15.00 USD per 
manual in Black & White, printing only the Front Cover (page1) in Color. 
 
Some of the pictures are in Color for the benefit of online viewing, but we print them in black & 
white. 
 
Thank you for your interest in our products!        Be Safe & Have Fun!!   Ed Pitman 

 
 

Delete This Page before printing!! 

 

To Keep Page Orientation Correct 

 
 

Summary of Contents for 912 Dragonfly
































































































































































































Reviews: