Installation and Operating Instruction for
B.E.G.
- Occupancy detector PD2-M-DALI/DSI-1C-DE
LUXOMAT
®
PD2-M-DALI/DSI-1C/PD2-S
EN
1. Product information
•
For group operation of up to 50 lights
•
Suitable for dimmable digital electronic ballasts and
control moduls
•
One additional switching channel for controlling lights and
HVAC (heating, ventilation, air conditioning) devices
•
DALI/DSI interface
•
Constant light control
•
Manual switching / dimming
•
Full or semi-automatic mode
•
Set value brightness, follow-up time – LIGHT/HVAC and
orientation light adjustable
•
Sensor and power supply in one housing
•
Infrared remote control
2. Operation
The presence detector controls the light automatically according
to people present (movements) and the ambient brightness.
The integrated light sensor constantly measures the ambient light
and compares it with the brightness level on the detector. If the
ambient light is sufficient, lighting will not be switched.
If the ambient light level is below the brightness level, a move-
ment activates the lighting in the room.
The detector switches the light off, if there is enough natural light
for 5 min. or if no movement is detected for one follow-up time.
The second channel can be interpreted as HVAC channel
(heating, ventilation, air conditioning). This channel switches the
connected load independent of the brightness.
3. Safety advice
!
Work on the 110-240V mains supply may only be
carried out by qualified professionals or by instructed
persons under the direction and supervision of quali-
fied skilled electrical personnel in accordance with
electrotechnical regulations
!
Disconnect supply before installing!
!
This device is not suitable for disconnection.
!
After having connected all cables, please mount the
cap onto the detector.
4. Mounting FC
A circular opening of diameter 68 mm must be drilled into the ceil-
ing. Having connected the cables in accor dance with regulations,
the detector is inserted into the opening as shown in the drawing
above and has to be fixed into position by means of the spring clips.
!
In Master/Slave operation, the master device must always
be installed at location with least daylight.
5.
Position DIP switches, LEDs
and potentiometers
PD2-
False ceiling
mounting
C
B
A
Light
measurement
DALI_D
SI
HV
AC_
LI
GHT
VA_HA
1
2
3
6. Self test cycle/Startup behavior
The product enters an initial 60-second self-test cycle, when the
supply is first connected. During this time, the device does not
respond to movement and stays on.
The initialization mode can be changed by using the remote
control.
7. Putting into operation / Settings
Twilight-switch for constant light control
The set value brightness can be adjusted at between 10 and
2000 Lux. Using the potentiometer, the set value brightness
can be adjusted as desired.
Symbol
: Night-time operation
Symbol
: Day/night time operation
Follow-up time for light control
The time can be set infinitely variably between
1 and 30 minutes.
Symbol
TEST
: Test mode
Every movement switches on the light independent of
brightness for a period of 1 second, switching it off for a
period of 2 seconds.
Orientation light
The follow-up time can be set infinitely variably at between
5 and 60 minutes. Manually switching ON/OFF the
orientation light.
„ON“ for permanent orientation light
„OFF“ for deactiviation of orientation light
Follow-up time for device control
The follow-up time can be adjusted between 5 min. and
120 min. The delay is active from a set time of >15 minutes.
This delay is about 5 min. If no other movements are detec-
ted during this time, the delay starts again.
Impulse function
The impulse function can be used to control external HVAC
systems. All 9 s will be set a 2.5 sec.
Alarm impulse
In order to initiate an alarm impulse, there have to be three
detected movements within a period of 9 sec.
This function can be used to display a presence in the room
on external visualizations. All 9 sec. will be set an impulse
of 2.5 sec.
The device does not fulfil the requirements of DIN EN50131-
2-2 and therefore cannot be used in professional intrusion
detection systems.
Pulse spacing PD-Slave
2 or 9 seconds can be set for the pause between 2 pulses
sent to the master. The setting can be made with activated
( ) or deactivated ( ) LED indicator.
For devices with a separate slave input, 2 sec.
can be set.
DIP switch functions
DIP 1
Fully automatic mode
(VA)
Semi-automatic mode
(HA)
DIP 2
HVAC function
Light control*
DIP 3
Operation mode DALI
Operation mode DSI
* If you select „LIGHT“, the switching relay R2 operates synchro-
nously to the DALI light channel. The potentiometer R2 has no
function in this setting.
Potentiometer A
Lux Channel 1
Potentiometer B
Time Channel 1
Potentiometer C
Orientation light
Potentiometer D
HVAC Channel 2
LED I
green
LED II
red
LED III
white
8. Wiring diagram
Standard mode with Master/Slave
L
N
L
N
N
N
S
Master
Slave
R
L
L
R
-
+
L‘
T1
DA1
M1
T2
DA
DA
E1 DALI/DSI
9. Manual switching and dimming
By pressing the push button, the phase can be given to the S
terminal.
To turn on or off, press the push button briefly. The light will remain
on or off, as people are detected plus the follow-up time.
With a long key press the light will be dimmed manually. When
you release the button, the current brightness value is retained.
Upon renewed dimming, the dimming direction is reversed.
Taking the phase to the R terminal by using a button, the HVAC
channel can be switched with a short key press.
10. Range
10 m
6 m
4 m
10 m
360°
2.50 m
2
1
1
2
quer zum Melder gehen
frontal zum Melder gehen
Unterkriechschutz
Walking across
Walking towards
Seated
!
Connected slaves must have the same phase
as the Master.
R1
TE
1
3
6
22
18 16
10
30
25
LUX
40
2000
600
1200
200
R2
A
120
60
5
15
30
40
50
20%
60
5
10
50 30
O
FF
ON
9s
2s
LED ON
LED OFF
R1
TE
1
3
6
22
18 16
10
30
25
LUX
40
2000
600
1200
200
R2
A
120
60
5
15
30
40
50
20%
60
5
10
50 30
O
FF
ON
R1
TE
1
3
6
22
18 16
10
30
25
LUX
40
2000
600
1200
200
R2
A
120
60
5
15
30
40
50
20%
60
5
10
50 30
O
FF
ON
!
R1
TE
1
3
6
22
18 16
10
30
25
LUX
40
2000
600
1200
200
R2
A
120
60
5
15
30
40
50
20%
60
5
10
50 30
O
FF
ON
68 mm
A
