www.balter.de
THC-D102IR
HD-TVI D
ome
C
amera
I
nsTallaTIon
m
anual
www
.
balTer
.
De
Thank you for purchasing our product. If there are
any questions, or requests, please do not hesitate to
contact the dealer.
This manual may contain several technicalincorrect
places or printing errors, and the content is subject
to change without notice. The updates will be added
to the new version of this manual. We will readily
improve or update the products or procedures
described in the manual.
P
rivacy
N
otice
Surveillance laws vary by jurisdiction. Check all
relevant laws in your jurisdiction before using this
product for surveillance purposes to ensure that
your use of this product conforms. Please refer to
the product specification for camera parameters
and functions.
Please refer to the product specification for camera
parameters and functions.
REGULATORY INFORMATION
Fcc i
NFormatioN
FCC compliance: This equipment has been tested
and found to comply with the limits for a digital
device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection
against harmful interference when the equipment
is operated in a commercial environment. This
equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instruction manual, may cause
harmful interference to radio communications.
Operation of this equipment in a residential area is
likely to cause harmful interference in which case the
user will be required to correct the interference at his
own expense.
Fcc c
oNditioNs
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received,
including interference that may cause undesired
operation.
eU c
oNFormity
s
tatemeNt
This product and - if applicable - the
supplied accessories too are marked
with «CE» and comply therefore with the
applicable harmonized European sstandards listed
under the Low Voltage Directive 2006/95/EC, the EMC
Directive 2004/108/EC, the RoHS Directive 2011/65/EU.
2012/19/EU (WEEE directive):
Products marked with this symbol cannot
be disposed of as unsorted municipal waste
in the European Union. For proper recycling,
return this product to your local supplier
upon the purchase of equivalent new equipment, or
dispose of it at designated collection points. For more
information see: www.recyclethis.info.
2006/66/EC (battery directive):
This product contains a battery that
cannot be disposed of as unsorted
municipal waste in the European Union.
See the product documentation for specific battery
information. The battery is marked with this
symbol, which may include lettering to indicate
cadmium (Cd), lead (Pb), or mercury (Hg). For proper
recycling, return the battery to your supplier or to a
designated collection point. For more information
see: www.recyclethis.info.
1. INTRODUCTION
1.1. P
rodUct
F
eatUres
This series of camera adopts new generation sensor
with high sensitivity and advanced circuit design
technology. It features high resolution, low mage
distortion and low noise, etc., which makes it uitable
for surveillance system and image processing system.
▪
High performance CMOS sensor and high
resolution bring high-quality image;
▪
Low illumination;
▪
OSD menu, parameters are configurable;
▪
Support auto white balance, auto gain control,
▪
Support image effect adjustment;
▪
Unit transmission control;
▪
Advanced 3-axis design meets different
installation requirements.
1.2. o
verview
1.2.1. o
verview
oF
t
yPe
i d
ome
c
amera
1.2.2. o
verview
oF
t
yPe
ii d
ome
c
amera
2. INSTALLATION
B
eFore
yoU
start
:
▪
Please make sure that the device in the package
is in good condition and all the assembly parts
are included.
▪
Make sure that all the related equipment is
power-off during the installation.
▪
Check the specification of the products for the
installation environment.
▪
Check whether the power supply is matched
with your power output to avoid damage.
▪
Please make sure the wall is strong enough to
withstand three times the weight of the camera
and the mounting.
▪
If the wall is the cement wall, you need to insert
expansion screws before you install the camera.
If the wall is the wooden wall, you can use self-
tapping screw to secure the camera.
▪
If the product does not function properly,
please contact your dealer or the nearest
service center. Do not disassemble the camera
for repair or maintenance by yourself.
2.1 i
NstallatioN
oF
t
yPe
i d
ome
c
amera
s
tePs
:
1. Drill the screw holes according to the drill
template.
2. Screw the clip plate onto the mounting base
loosely.
Figure 2-1 The Drill Template
Figure 2-2 Screw the Clip Plate
HD Video Cable
Mounting Base
Camera
Trim Ring
Enclosure
Power Cable
Side Opening
Enclosure
HD Video Cable
Mounting Base
Power Cable
Camera
Trim Ring
Screw hole
Clip Plate
1.2.3 o
verview
oF
t
yPe
iii d
ome
c
amera
Enclosure
Camera
HD Video Cable
Power Cable
Mounting Base
3. Fix the mounting base to the ceiling with the
supplied screws.
4. Route the cables to the cable hole and connect
the corresponding power cable and video cable.
5. Pull out the clip plate and secure the camera
with the trim ring to the mounting base.
6. Push the clip plate in and tighten the lock screw
to secure the trim ring.
