background image

1

Sales 800-633-0405

www.productivity2000.com

1   OVER

2J 0526

3E 1000

4  UNDER

5   OVER

6 21.35

7 1.245

8  SPARE

°

C

°

F

M

V

M

V

2000

P2-08THM Analog Input

The P2-08THM Thermocouple Input Module 

provides eight differential channels for receiving  

thermocouple and voltage input signals for use

with the Productivity2000 System.

General Specifications   . . . . . . . . . . . . . . . . . . . . . . 1

T/C Input Specifications   . . . . . . . . . . . . . . . . . . . . . 2

Voltage Input Specifications   . . . . . . . . . . . . . . . . . . 2

Configuration/Diagnostics  . . . . . . . . . . . . . . . . . . . . 2

Wiring Diagram and Schematic . . . . . . . . . . . . . . . . 3

Module Installation Procedure . . . . . . . . . . . . . . . . . 4

QR Code  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Hot Swap Information  . . . . . . . . . . . . . . . . . . . . . . . 4

Wiring Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Module Configuration   . . . . . . . . . . . . . . . . . . . . . . . 5

Typical Application Example  . . . . . . . . . . . . . . . . . . 6

OLED Panel Display Menus  . . . . . . . . . . . . . . . . . . 7

Warning  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Removable Terminal Block Specifications. . . . . . . .  8

General Specifications

Operating Temperature

0º to 60ºC (32º to 140ºF)

Storage Temperature

-20º to 70ºC (-4º to 158ºF)

Humidity

5 to 95% (non-condensing)

Environmental Air

No corrosive gases permitted

Vibration

IEC60068-2-6 (Test Fc)

Shock

IEC60068-2-27 (Test Ea)

Field to Logic Side Isolation

1800VAC applied for 1 second

Heat Dissipation

500mW

Enclosure Type

Open Equipment

Agency Approvals

UL508 File E139594, Canada & USA 

CE (EN61131-2*)

Module Keying to Backplane Electronic
Module Location

Any I/O slot in a Productivity2000 System

Field Wiring

Removable terminal block (included). 

The P2-08THM module is not compatible with the 

ZIPLink wiring system.

EU Directive

See the “EU Directive” topic in the Productivity2000 

Help File. Information can also be obtained at: 

www.productivity2000.com

Connector Type (included)

18-position removable terminal block

Weight

90g (3.2 oz)

*Meets EMC and Safety requirements. See the D.O.C. for details.

Terminal Block Included. Not Compatible with ZIPLink.

Warranty: Thirty-day money-back guarantee. Two-year limited 

replacement. (See www.productivity2000.com for details).

Summary of Contents for PRODUCTIVITY 2000









Reviews: