REMOTE TRANSMITTER OPERATION:
System Function
Remark
Arm & Lock Doors
Press the Lock button for a half second
Silent Arm & Lock Doors
Press and hold for 1.0 seconds
Panic Function
Press and hold for 3 seconds to Activate or Deactivate
panic function
-
Arm and Warn-Away Bypass
Press Twice within 3 seconds.
-
-
Arm and Warn-Away & Shock Sensor
Bypass
Press button 3
times within 3 seconds.
-
Arm and Tilt Sensor Bypass
Press the button first then press
button
-
2 sec.
Arm and All Sensors Bypass
Press 2 times and hold the second times for 2
seconds
1 sec.
-
Arm and Hidden Alarm Function
Press and hold
button for 1 sec. first then press and
release button
Disarm & Unlock Doors
Press the Unlock button for a half second
Silent Disarm & Unlock Doors
Press and hold for 1.0 seconds
Passive Arming Bypass
Press and hold for 3 seconds
-
Disarm & Two Steps
Door Unlock (optional)
Press twice within 3 seconds
Trunk Release (Aux 1)
Press and hold for 3 seconds
1 sec
.
-
Car Finder
Press and hold
button for 1 sec. first then press &
release
button.
Activate or Deactivate
the Remote Start
Press button once.
Press button twice if set to start safety mode.
Runtime Reset
Press and hold for 2 seconds
-
Timer Start
Press the
button first then
press button.
+
Turbo Mode
Press and hold for 2 seconds
+
Aux 2 Timer Output
Press together & release.
+
Switch Code for 2
nd
Car Operation
Press and hold for 2 seconds
+
Shutdown Diagnostic
Press and hold for 2 seconds
ALARM OPERATING CONDITION
LED On Duty
Sir en / Hor n
Par king Light
LED
Door s
Star ter
Dome Light
Arming
1 or 3 Chirps
1 Flash
Slow Flash
Locking
Disable
Disarming
2 or 4 Chirps
2 or 3 Flashes
OFF
Unlocking
Turns on for 30-
Seconds
Trigger
Alarming
Flashes
Flashes Pause
Disable
Flashes
Hidden Alarm
Flashes
Slow Flash
Disable
Flashes
Passive Arming
Fast Flash
Panic
Alarming
Flashes
Flashes
Car Finder
6 Chirps
12 Flashes
Locking
CHANGING THE BATTERY
The One-w ay remote is powered by one CR2032 Battery. To replace battery use a coin or small flat blade screwdriver to
carefully pry apart case
ACTIVE ARMING
– LOCK & ARM
1.
Press the button on the transmitter.
2.
The alarm arms, doors lock (if connected), and the siren chirps and parking lights flash once.
3.
If Valet Mode* is ON, the doors lock Exit Valet Mode to arm the alarm normally.
DEFECTIVE SENSOR REMINDER:
If the siren sounds 3 chirps and the defective then you have left a door, trunk, or hood lid ajar.
(See feature bank 1-06)
SILENT ARMING:
Press and hold the transmitter buttons for 1.0 second. This will arm your security system. No chirp sound
will be heard and the arm confirmation will be through the vehicles parking lights only.
WARN-AWAY BY-PASS:
Press button twice will arm the security system and by-pass
the
warn-away
.
Note:
The bypass feature is programmed to activate for one arming cycle only. The security system will return to normal operation
during the next arming cycle.
SHOCK SENSOR BY-PAS
S: Press the button 3 times within 3 seconds, it will arm the security system and bypass the shock
sensor
.
TILT SENSOR BY-PASS: Press
the button first then press
button within 3 Seconds. It will arm the security system and by-
pass the tilt sensor
ALL SENSORS BYPASS:
Press button
2
times within 3 seconds and hold on second time for 2 seconds until the beep
confirms then release the button. It will arm the security system and bypass all sensors.
HIDDEN ALARM FUNCTION:
The security system will arm and with “ Hidden Alarm Function”, the siren / horn will be silenced
even if the sensor is triggered in the armed mode. Press and hold the
button for 1 second until the back light turns on then
press the button will Arm the security system and activate the hidden alarm function.
PASSIVE ARMING:
(See feature bank 1-08)
Active arming / disarming is controlled by your security system via the remote transmitter. This
security system is equipped with an
optional Passive Arming feature which allows the security
system to arm 30 seconds after the last door is closed. Operation is as
follows:
1.
Turn the ignition to the
“OFF”
position and exit the vehicle.
2.
After all entrances are closed, the security system LED will flash fast for 30 seconds. If you reopen any door / hood / trunk, the
security system LED will stop flashing. It will begin flashing again once all vehicle entrances are closed.
3.
After the 30-second time has elapsed, the security system will automatically “ ARM” .
4.
The siren will chirp [1] time and the parking lights will flash [1] time.
PASSIVE ARMING WITH PASSIVE DOOR LOCKING:
The vehicle doors will automatically lock after the passive arming cycle has
been completed.
PASSIVE ARMING BY-PASS
:
While the system is disarmed, press and hold the button for 3 seconds
until the beep
confirms and then release the button. The system will respond with [1] chirp and the LED stop to flashes. The security system will
remain in this temporary state for as long as you wish.
To exit Passive arming by-pass
, press the transmitter or button and the system will return to normal status.
1.
Press the button on the transmitter, and beeps play to confirm.
2.
The siren will chirp twice and the parking lights will flash twice indicating that the security
system is now disarmed. The vehicle’s doors will unlock and the dome light will turn on
for 30 seconds upon disarming.
Note:
Power door locks and dome light must be installed with the security system.
ACTIVE DISARMING
– UNLOCK & DISARM
SILENT DISARMING
:
Press and hold the transmitter buttons for 1.0 second. This will disarm your security system.
No chirp
sound will be heard and the disarm confirmation will be through the vehicles parking lights only,
TAMPER DISARMING:
If the alarm has been triggered, upon disarm the system’s siren will chirp 4 times and the parking lights
will flash 3 times telling you the alarm has been triggered during the last armed state
AUTOMATIC RE-ARM:
If this feature is selected, the security system will automatically re-arm itself in 60 seconds after
disarming with remote transmitter. Automatic rearm will cancel if any door is opened before the 60 seconds timer has elapsed.
(See the feature bank
1-09
).
TRIGGER THE SYSTEM:
When armed, your vehicle is protected as follows: Light impact will trigger the warn-away signal. Heavy
impacts / Doors open / Trunk open / Hood open / Turn on the ignition key / lift the vehicle will trigger the programmed sequence
.
The starter disable relay (if installed) prevents the vehicle’s starter from cranking. The siren, horn, parking lights, and dome light
will turn on for 30 seconds, alerting of an intrusion. It will then stop, automatic reset and re-arm. If any one of the sensors or
detectors are still active, the alarm system will sound a maximum of 3 cycles. Each cycle is a 30 seconds alert.
NOISE ABATEMENT CIRCUIT:
Your system has a “Noise Abatement Circuit”. It prevents annoying repetitive trigger sequences
due to faulty door pin switches or environmental conditions such as thunder, jackhammers airport noise, etc.
Here’s how “Noise Abatement Circuit” works:
The alarm triggers five times. Each time, it's all shock sensor triggers the alarm;
the “ Noise Abatement Circuit” will interpret this pattern of triggers as a false alarm. After the fifth trigger, the “Noise Abatement
Circuit” ignores, or bypasses the shock sensor until a different sensor or switch is triggered.
“Noise Abatement Circuit”
covers doors (Trunk / Hood / Tilt Sensor / Ignition Switch) differently: If the alarm is triggered by an
open door for three full cycles, the doors will be bypassed until the trigger ceases.
PANIC FUNCTION:
Press and hold the button for 3 seconds until the beep confirms and then release the button to
activate the personal protection alarm
The alarm Arms (or Locks in Valet) and, sounds the siren and flashes the parking lights
for 30 seconds. Press the button for 3 seconds to stop the output.
DISARMING WITHOUT A TRANSMITTER
(See feature bank
1-10
)
Number of presses ___
1.
Turn the ignition on.
2.
Press and release the button on the valet switch the correct number of times (the default is
one press
).
3.
After a few seconds, the siren output ceases, and the system is disarmed.
VALET MODE:
When servicing or loaning your vehicle to others, the system should be placed in Valet Mode. Valet Mode
prevents the system from remote starting and disables all alarm functions.
Enter Valet Mode:
1.
Under disarmed, turn the ignition to
ON
position.
2.
Press and hold valet switch for 2 seconds until the LED turns
“ON”
solid
The LED will remain on as long as the system is in Valet Mode.
Exit Valet Mode:
1.
Turn the ignition switch to
ON
.
2.
Push and hold the valet switch for 2 seconds. The LED will turn off indicating the system is exiting the Valet Mode.
