background image

A U T O M A T I C   T R A N S M I S S I O N   R E M O T E   S T A R T E R

AS-2510 TW

Installation Guide 

A note concerning the battery inside the transmitter:

Depending on the usage of the transmitter, the battery can last anywhere between 3 to 6
months.  When the battery is low, it the transmitter will emit two beeps in a repetitive
cycle.  At that point you should replace your battery with a new one.  That is why we
recommend that you keep a spare battery somewhere handy such as the glove
compartment.

Notice

The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of 
the product, be that either damage to the vehicle itself or to the Unit. This Unit must be installed by a certified
technician using all safety devices supplied. Please note that this guide has been written for properly trained
Autostart technicians: a certain level of skills and knowledge is therefore assumed. Please review the
Installation Guide carefully before beginning any work.

Warning

This Remote Car Starter is designed for vehicles with an

automatic

Transmission only. Before

installing the Unit, test that the vehicle does not start when the Gear Select Lever is in the “Drive” position. If it 
starts in gear, install a manual-transmission remote starter system instead.

DOC

 .1.00

 – November 5, 2003 

Gp CA Lp 

Manufactured in Canada by Autostart

Summary of Contents for AS-2510 TW




















Reviews: