AussieCarHoists YL-250 Installation And Operation Manual Download

Page: 1 / 47

This instruction manual has been prepared especially for the operator of this equipment. Your new lift is the product of over

15 years of continuous research, testing and development, it is the most technically advanced lift on the market today.

READ THIS ENTIRE MANUAL BEFORE INSTALLATION &

OPERATION COMMENCES

YL-250

5000KG 5 TON BASE PLATE

CAR HOIST

Installation and operation manual

READ FIRST

Do not operate this machine

until you have read and

understood all dangers, warnings

and cautions in this manual

YOUR

SAFETY

OUR

STANDARDS

IMPORTANT SAFETY INSTRUCTIONS

KEEP THESE INSTRUCTIONS ON HAND. PLEASE READ THE ENTIRE CONTENTS OF THIS MANUAL PRIOR TO INSTALLATION AND

OPERATION. BY PROCEEDING WITH LIFT INSTALLATION AND OPERATION YOU AGREE THAT YOU FULLY UNDERSTAND THE FULL

CONTENT OF THIS MANUAL. FORWARD THIS MANUAL TO ALL OPERATORS. FAILURE TO OPERATE THIS EQUIPMENT AS DIRECTED

MAY CAUSE INJURY OR DEATH.

KEEP THIS OPERATION MANUAL NEAR THE MACHINE AT ALL TIMES. ENSURE ALL USERS READ THIS MANUAL.

RECEIVING

Ensure shipment is thoroughly inspected as soon as received.
The signed Bill of Lading is acknowledgement by the shipping

carrier as receipt that this product as listed on invoice is in good

condition for shipment. For your protection: If any goods listed on

this Bill of Lading are missing or damaged, do not accept goods

until the shipping carrier makes a notation on the freight bill of

the missing or damaged goods.

BE SAFE

Your hoist was designed and built with safety in mind. To

increase your overall safety operate with proper training

and thoughtful operation. DO NOT operate or repair this

equipment without reading this manual and the important

safety instructions included throughout. Ensure ALL USERS

read and understand this manual.

HIGH-LIFT

Summary of Contents for YL-250
















































Search results

Summary of Contents for YL-250

Reviews:

Related manuals for YL-250

Brands by name

Popular brands

AussieCarHoists YL-250, Installation And Operation Manual

Search results

Summary of Contents for YL-250

Reviews:

Related manuals for YL-250

Brands by name

Popular brands