Audiovox Platinum+ APS 687C Installation Manual Download

Page: 1 / 28

128-8783b

1 of 28

Model APS-687C

Installation Manual

Vehicle Security System

with Remote Start

Rev B: New Format Add Timing PASD & Light Blue + DBI Lock, Lock, Lock 5/2013
If booklet format, pages 26-30, Programming & Wiring Diagram shall be foldout or seperate 5 sheets
front & back.

PATENTED: www.voxxintl.com/company/patents

Table Of Contents:

Before You Begin

Page 2

Wire Harnesses Quick View

Page 3 - 4

Installation Of The Major Components

Page 5

6 Pin Power Harness Wiring

Page 6

4 Pin Alternate Ignition Harness Wiring

Page 7

12 Pin Accessory Input/Output Harness Wiring

Page 8 -11

5 Pin Aux Channel Output Harness

Page 11 - 12

Door Lock Harness Wiring

Page 13 -15

3 Pin Input/Output Harness Wiring

Page 15

4 Pin Auxiliary Output Harness Wiring

Page 16

2 Pin Transponder Harness Wiring

Page 16 -17

Telematic Port Information

Page 17

5 Pin Antenna Harness

Page 17

DBI Port Information

Page 17

Time Start Program

Page 17-18

Diesel Engine Settings

Page 18

Tach Rate Setting

Page 19 -27

Engine Monitoring Selections, (Voltage Tach, DBI, Hybrid,)

Page 18 -19

Diagnostics Access & Information

Page 19

Multi Coil Pack Adaptor Optional

Page 19 - 20

Testing Your Installation Hood Pin Safety

Page 20

Manual Override Safety Testing and Operation

Page 20 - 21

Neutral Safety Switch Testing

Page 21 - 23

Completing Your Installation

Page 23

Programming Transmitters

Page 24

Programming Alarm Feature Bank 2

Page 24 - 25

Programming Remote Start Feature Bank 3

Page 26 - 27

Circuit Wiring Layout

Page 28

Summary of Contents for Platinum+ APS 687C





























Search results

Summary of Contents for Platinum+ APS 687C

Reviews:

Related manuals for Platinum+ APS 687C

Brands by name

Popular brands

Audiovox Platinum+ APS 687C, Installation Manual

Search results

Summary of Contents for Platinum+ APS 687C

Reviews:

Related manuals for Platinum+ APS 687C

Brands by name

Popular brands