background image

# 44876D006

Page 1

Save these instructions for future reference

INSTALLATION AND MAINTENANCE

INSTRUCTIONS

EF Electric Furnace

Manufactured By

A.A.C.

A Lennox International Inc. Company

421 Monroe Street

Bellevue, OH 44811

Inspection of Shipment

Upon receipt of equipment, carefully inspect it for possible
shipping damage. If damage is found, it should be noted
on the carrier’s freight bill. Take special care to examine
the unit inside the carton if the carton is damaged. Any
concealed damage discovered should be reported to the
last carrier immediately, preferably in writing, and should
include a request for inspection by the carrier’s agent.

If any damages are discovered and reported to the carrier
DO NOT INSTALL THE UNIT

, as claim may be denied.

Check the unit rating plate to confirm specifications
are as ordered.

TABLE OF CONTENTS

INSTALLATION ....................................... 2

SETUP PROCEDURE ........................... 6

SEQUENCE OF OPERATION ............... 8

SYSTEM CHECK ................................... 9

REPLACEMENT PARTS ...................... 10

MAINTENANCE ................................... 10

AIRFLOW CONFIGURATIONS ............ 11

WIRING DIAGRAMS ............................ 12

WARRANTY ......................................... 15

*44876D006*

The information contained in this manual is
intended for use by qualified service techni-
cians familiar with safety procedures and
equipped with the proper tools and test in-
struments. Failure to carefully read and follow
all instructions in this manual can result in
equipment malfunction, property damage,
personal injury, and/or death.

  WARNING

Disconnect all power supplies to both the
indoor blower section and outdoor section
before making any electrical connections or
servicing the system. More than one discon-
nect switch may be required to de-energize
the equipment. Hazardous voltage can
cause severe personal injury or death.

  WARNING

Improper installation, adjustment, service, or maintenance can cause injury or prop-
erty damage. Refer to this manual. For assistance or additional information, consult
a qualified installer or service agency.

 

WARNING

0650329-50 / 44876D006

Summary of Contents for EFC08
















Reviews: