![background image](http://html1.mh-extra.com/html/american-standard/studio-right-height-2794/studio-right-height-2794_installation-instructions-care-and-maintenance_2929910001.webp)
RECOMMENDED TOOLS AND MATERIALS
Putty Knife
Regular Screwdriver
Adjustable Wrench
Sealant
Tape Measure
Hacksaw
Wax Ring/Gasket
Flexible Supply Tube
Closet Bolts
Carpenters Level
1
REMOVE OLD TOILET
a. Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.
b. Disconnect and remove supply line. NOTE:
If replacing valve, first shut off main water supply!
c. Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.
d. Remove closet bolts from flange and clean away old wax, putty, etc. from base area.
NOTE:
Mounting surface must be clean and level
before
new toilet is installed!
S
A
VE FOR FUTURE USE
2
7 3 016 9 2 - 10 0 Rev. C
CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!
NOTE:
Pictures may not exactly define contour of china and components.
Right Height
®
, Elongated Model 2794
Right Height
®
, Round Front Model 2795
Studio
®
Dual Flush Concealed Trapway
INSTALLATION INSTRUCTIONS
CARE AND MAINTENANCE
Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this
product is installed properly, please read these instructions carefully before you begin. (Certain installations
may require professional help.) Also be sure your installation conforms to local codes.
!
ROUGHING-IN
DIMENSIONS:
NOTE:
Distance from wall to
closet flange centerline must
be as listed below:
IMPORTANT:
Water supply
on the wall is required at
2-1/4" or 8" from centerline
of the toilet (see rough-in).
First suggested position is
hidden behind the toilet. The
geometry of the toilet gives
space for this installation.
The second suggested
position is next to the toilet.
Between these two
positions, the space for the
supply between wall and
toilet is limited to 4-1/2". In
this case, check your supply
and hose dimensions.
Certified by
IAPMO R&T
IMPORTANT: Water supply on the wall is required at 2-1/4" or 8" from centerline of the toilet (see rough-in).
First suggested position is hidden behind the toilet. The geometry of the toilet gives space for this installation.
The second suggested position is next to the toilet. Between these two positions, the space for the supply
between wall and toilet is limited to 4-1/2". In this case, check your supply and hose dimensions.
2-1/4"
(57mm)
30-1/4"
(768mm)
8-3/4"
(221mm)
1-1/8"
(29mm)
18-1/2"
(470mm)
4-1/2"
(1
1
4
mm)
3-1/8"
(81mm)
2-5/8"
(67mm)
7-1/2"
(191mm)
13-11/16"
(347mm)
12-3/16"
(309mm)
16-1/2"
(419mm)
15-3/4"
(399mm)
30-7/8"
(784mm)
12"
(305mm)
FINISHED
FLOOR
FINISHED
WALL
C/L OF SEAT POST
HOLES 5-1/2"
(140mm) CENTERS
SUPPLY
AS
REQUIRED
(position 1 or
position 2)
6"
(152mm)
5-1/2"
(140mm)
14"
(356mm)
8"
(204mm)
BACK VIEW
(for reference)
RIGHT HEIGHT ELONGATED 2-PIECE TOILET
RIGHT HEIGHT ROUND FRONT 2-PIECE TOILET
IMPORTANT: Water supply on the wall is required at 2-1/4" or 8" from centerline of the toilet (see rough-in).
First suggested position is hidden behind the toilet. The geometry of the toilet gives space for this installation.
The second suggested position is next to the toilet. Between these two positions, the space for the supply
between wall and toilet is limited to 4-1/2". In this case, check your supply and hose dimensions.
2-1/4"
(57mm)
28-1/4"
(717mm)
8-3/4"
(221mm)
1-
1/8"
(29mm)
16-1/2"
(419mm)
4-1/2"
(1
1
4
mm)
3-1/8"
(81mm)
2-5/8"
(67mm)
7-1/2"
(191mm)
12-7/8"
(328mm)
12-3/16"
(309mm)
16-1/2"
(419mm)
15-3/4"
(399mm)
30-7/8"
(784mm)
12"
(305mm)
FINISHED
FLOOR
FINISHED
WALL
C/L OF SEAT POST
HOLES 5-1/2"
(140mm) CENTERS
SUPPLY
AS
REQUIRED
(position 1
or
position 2)
6"
(152mm)
5-1/2"
(140mm)
14"
(356mm)
8"
(204mm)
BACK VIEW
(for reference)
P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A S A m e r i c a , I n c .
© A S A m e r i c a , I n c . 2 0 1 2