background image

Quick Start Guide, 61700601G2-13D, November 2009

1

N

ET

V

ANTA

 3100 S

ERIES

 R

OUTER

P/N 1700601G2, 1700611G2, 1700612G2

4

Copyright © 2009 ADTRAN, Inc. All Rights Reserved.

G

ETTING

 S

TARTED

Two configuration methods are available for your NetVanta router:

Web-based graphical user interface (GUI)

AOS command line interface (CLI)

The GUI lets you configure the main unit settings, and provides online guidance, explanations for 
each setting, and configuration wizards to help you get started. However, using the AOS CLI may 
be necessary for more advanced configurations. 

A

CCESS

 

THE

 GUI

You may access the GUI from any Web browser on your network by following these steps:
1.

Connect the router to your PC, using an Ethernet cable connected to one of the four ports on 
the back of the unit (

Ethernet 1

,

 2

,

 3

, or

 4

).

2.

Connect the router to your service provider connection, using the provided cable connected 
to the 

ETH 0/1

 port on the router (for the NetVanta 3120). If you have a NetVanta 3130, plug 

your ADSL line into the port labeled 

ADSL

 on the back of the unit.

3.

After the router is connected to the PC, make sure the router is powered. Remember to plug 
the unit in and to turn the unit on using the toggle switch at the rear of the unit.

4.

During bootup, your PC will obtain an IP address from the NetVanta 3100 Series unit’s 
DHCP server. By default, both the DHCP and HTTP servers are enabled. 

5.

Enter the unit’s IP address in your browser address line. The default IP address is 

10.10.10.1

.

6.

You will then be prompted for the username and password (the default settings are 

admin

 

and 

password

).

7.

The initial GUI screen appears. You can access initial setup information by selecting 

Setup 

Wizard 

from the menu on the left.

For security purposes, you should set up an 

admin

 password 

immediately. Use the 

Passwords

 menu of the GUI to change this 

password. 

By default, the NetVanta 3130 comes with an ADSL and an 
asynchronous transfer mode (ATM) port already configured and 
enabled. The service provider should provide a PVC (VPI/VCI) number, 
which will be used to configure the ATM PVC.

C

ONFIGURE

 Y

OUR

 A

PPLICATION

The applications you will need to configure vary by product and by network. Review the list of 
defaults for your unit (included in the next section) before deciding what applications to configure. 
Some common applications that should be configured on startup are addressed in the articles 
listed below. You can access these articles online at 

http://kb.adtran.com

.

Additional detailed documentation for configuring your ADTRAN unit is provided on the 

AOS 

Documentation

 CD included in your shipment. For more detail on hardware setup, refer to the 

appropriate NIM quick start guides and the appropriate hardware installation guide. For more 
detail on configuring your system, refer to the 

AOS Command Reference Guide

, configuration 

guides, and technical support notes available on the 

AOS Documentation

 CD or online at 

http://kb.adtran.com

.

N

ET

V

ANTA

 3100 S

ERIES

 D

EFAULTS

Configuring Internet Access (Many to 

one NAT) with the Firewall Wizard in 

AOS (video article 2185)

Configuring Port Forwarding in AOS 

(video article 2291)

Configuring QoS for VOIP in AOS 

(video article 3091)

Configuring ADSL Internet Access in AOS 

(article 1965)

Configuring QoS in AOS 

(article 1617)

Configuring DHCP Server in AOS 

(article 2149)

Configuring a VPN using Main Mode in 

AOS (article 1925)

Configuring a VPN using Aggressive Mode in 

AOS (article 1926)

Important:

 For additional details on product features, specifications, 

installation, and safety, refer to the appropriate hardware installation 
guide on the 

AOS Documentation

 CD shipped with the base unit and 

available online at

 

http://kb.adtran.com

.

Feature

Default Value

IP Address

10.10.10.1

Username

admin

Password

password

HTTP Server

Enabled

Event History

On

IP Routing

Enabled

DHCP

Enabled

VLAN Interface

Enabled (

vlan 1

) with IP address 10.10.10.1

Firewall

Enabled

NAT

Overload to 

eth 0/1

 address (3120)

Overload to 

ppp 1

 address (3130)

Summary of Contents for 1700601G2

Page 1: ... a NetVanta 3130 plug your ADSL line into the port labeled ADSL on the back of the unit 3 After the router is connected to the PC make sure the router is powered Remember to plug the unit in and to turn the unit on using the toggle switch at the rear of the unit 4 During bootup your PC will obtain an IP address from the NetVanta 3100 Series unit s DHCP server By default both the DHCP and HTTP serv...

Page 2: ...ult IP address is 10 10 10 1 2 You will then be prompted for the user name and password the default settings are admin and password 3 Enter enable at the prompt 4 Enter the enable password when prompted The default password is password FACTORY DEFAULT SWITCH If the factory default switch shown in the illustration above is pressed during bootup while the STAT LED is flashing green the unit will sta...

Page 3: ...ively disabled or does not have link 3120 only Green solid The port is enabled and the link is up Amber flashing The port has activity transmit or receive WAN Off The interface is administratively down 3130 only Green solid The link is up and everything is operational Red solid An alarm condition is occurring on the WAN interface or there is a self test failure Amber solid The unit is in test VPN ...

Page 4: ...es available on the AOS Documentation CD or online at http kb adtran com NETVANTA 3100 SERIES DEFAULTS Configuring Internet Access Many to one NAT with the Firewall Wizard in AOS video article 2185 Configuring Port Forwarding in AOS video article 2291 Configuring QoS for VOIP in AOS video article 3091 Configuring ADSL Internet Access in AOS article 1965 Configuring QoS in AOS article 1617 Configur...

Reviews: