job
Aid
D
ESCRIPTION
The
Small
Form
‐
Factor
Pluggable
10
Gigabit
Ethernet
XFP,
1550
nm,
Commercial
Temperature
(XFP)
optical
transceiver
is
a
fully
duplex
serial
electric,
serial
optic
device
with
both
transmit
and
receive
functions
contained
in
a
single
module
that
provides
a
high
speed
serial
link
at
10
Gb/s.
Installed
into
an
appropriate
host
module,
the
XFP
provides
a
10
Gigabit
interface
to
the
supporting
system.
The
transmit
side
of
the
XFP
converts
serial
NRZ
electrical
date
at
the10
Gb/s
line
rate
to
a
standard
compliant
optical
signal.
The
receive
side
of
the
XFP
converts
the
incoming
DC
balanced
serial
NRZ
optical
data
at
the
10
Gb/s
line
rate
into
serial
electrical
data.
NOTE
To
ensure
compatibility,
refer
to
the
documentation
provided
with
the
host
module.
The
following
features
are
supported
on
the
XFP:
♦
1550
nm
optical
signals
for
up
to
80
km
reach
♦
Low
power
consumption
(<3.5
W
max)
♦
Excellent
EMI
performance
♦
Bit
error
rate
10^
‐
12
CAUTION
!
Due
to
compliance
certification
requirements,
only
XFPs
supplied
by
ADTRAN
are
to
be
used
with
the
host
module.
ADTRAN
cannot
certify
system
integrity
with
other
XFPs.
Operational Specifications
♦
Optical
Specifications:
◊
Transmit
Wavelength:
1550
nm
◊
Receive
Wavelength:
1530
to
1565
nm
◊
Data
rate:
9.95
Gb/s
to
11.1
Gb/s
◊
Optical
transmit
level:
0
to
+4.0
dBm
Small Form-Factor Pluggable
10 Gigabit Ethernet XFP, 1550 nm
Commercial Temperature
◊
Optical
receive
level:
greater
than
–24dBm
◊
Optical
distance:
80
km
maximum
◊
Optical
connectors:
LC
♦
Extended
Environmental
Support:
◊
Operational
temperature
range:
0°C
to
+70°C
◊
Storage
temperature
range:
–40°C
to
+85°C
◊
Relative
humidity
to
85%,
noncondensing
I
NSTALLATION
Inspect
the
XFP.
If
damaged,
file
a
claim
with
the
carrier
and
then
contact
ADTRAN
Customer
Service.
To
install
the
XFP
into
an
appropriate
module,
complete
the
following
steps:
1. Insert
the
XFP
into
the
XFP
cage
on
the
circuit
board
of
the
host
module
with
the
latch
handle
facing
outward.
Slide
the
XFP
all
the
way
into
the
receptacle.
NOTE
The
latch
on
the
XFP
is
for
removal
only.
When
removing
the
XFP,
rotate
the
latch
away
from
the
XFP
cage
until
a
physical
click
occurs.
The
XFP
should
slide
easily
out
of
the
cage.
2. Using
thumb
and
forefinger,
exert
adequate
pressure
to
ensure
the
XFP
is
completely
seated
in
the
XFP
cage.
3. Do
not
remove
the
connector
plug
until
the
optical
fiber
connection
is
made.
NOTICE
It
is
recommended
that
the
connector
plug
remain
on
whenever
the
transceiver
optical
fiber
connector
is
not
inserted.
4. Continue
the
installation
and
turn
‐
up
of
the
host
module
using
the
instructions
in
the
Job
Aid
provided
with
that
module,
or
using
the
Installation
and
Maintenance
Practice
(I&M),
available
online
at
www.adtran.com
.
P
ROVISIONING
The
XFP
is
not
directly
provisionable.
To
provision
the
XFP,
access
the
menu
system
of
the
host
module.
Refer
to
the
“Provi
‐
sioning”
section
of
the
Job
Aid
or
Installation
and
Maintenance
Practice
provided
with
the
host
module
for
provisioning
details.
CLEI: BVL3AGKD_ _
Product P/N: 1442980G1C
Issue Date: 0909
Document P/N: 61442980G1C-22A
