BODYTESTER
Instruction Manual
BODYTESTER
infrared thermometer
INTRODUCTION
This infrared thermometer determines surface temperature of an object by measuring infrared
energy radiated from object surface. It is a noncontact forehead infrared thermometer designed
specifically for measuring forehead temperature of human body. It cannot be used for other
body parts.
APPLICATION SCOPE
The temperature of subject is measured by radiation from forehead.
The thermometer is applicable to infant, children, and adults
Age Normal temperature
0-2 36.1-37.3 °С
3-10 36.4-37.3 °С
11-65 35.9-37.3 °С
≥65 35.8-37.3 °С
PRODUCT ADVANTAGES
1. Three- color backlight and fever indicator ;
2. Two measurement modes can be switched;
3. Automatic shutdown after 20s(±2s) of no operation;
4. Fever indicator time can be set;
5. Temperature correction setting;
6. 32 groups of measurement data can be stored;
7. Silent mode setting;
8. Switch between centigrade degree and Fahrenheit degree.
PREVENTIVE INSPECTION
Please check the appearance of instrument before use. If it isdamaged, it is recommended to
stop test. Please check whether batteries are fully charged before use. If thebattery is low, it is
recommended to replace batteries. Please read this manual carefully before use.
When measuring body temperature, please ensure that the thermometer is in a stable envi
-
ronment. It is recommended not to test inplaces with big vent such as fan and air conditioner;
Please do not use the instrument in the environment of magneticinterference; If the measured
object comes from where temperature differs greatlyfrom that of measured environment,
please wait for at least 5 minutesbefore measurement.
Please do not measure body temperature right after measuringextremely high or low tempera
-
ture, wait for at least 15 minutes beforemeasurement. Body temperature may change slightly
after doing sports, havingshower or meal, wait for at least 30 minutes before measurement.
When measuring body temperature, it is recommended to takemultiple measurements, which
-
ever appears more often. Please keep the inner space of sensor clean before or after use. After
measurement, if the result differs from expectation, it isrecommended to use contact thermom
-
eter ( such as mercury thermometer) as reference. Please do not crash or drop the thermom
-
eter, and stop using it forany damage. Use alcohol gently clean the surface of thermometer.
Important reminding:
1) Before measurement, make sure the measured part on forehead clean, for instance, no hair,
sweat, dust, etc.
2) Please choose body temperature mode to measure forehead temperature, and calibration
mode to measure surface temperature of object.
3) The thermometer applies to body temperature measurement of all ages.
4) The red backlight indicates abnormal body temperature, which is an emergency and requires
immediate medical attention.
5)When the instrument detects unstable environment temperature, it reports error and main
screen displays icon.
WARNINGS:
a. Keep the thermometer out of children’s reach.
b. Do not throw thermometer or battery into the fire.
c. This product is not water-proof, please do not put
it in water.
d. This product cannot replace doctor’s diagnosis.
PRODUCT COMPOSITION
1. Body temperature/ calibration switch button
2. Temperature sensor
3.“-”button
4.“+” button
5. Setting button
6. Measurement button/ Power button
7. Battery door
8. LCD
LCD DESCRIPTION
1. Body temperature mode indicator
2. Calibration mode indicator
3. Buzzer indicator
4. Temperature unit
5. Stored data
6. Stored data serial number
7. Low battery indicator
8. Data storage indicator
9. Temperature value
OPERATION INSTRUCTION
1. Inspection
Check whether the package is compact and undamaged, then unpackage and take the
thermometer out.
2. Temperature measurement
1) open battery door and install two AAA batteries in right polarity “+” and”-“, then close
battery door.
2) Press power button to turn on the thermometer.
3) After startup, point sensor at the measured object and press measurement button
( for object if not human body, switch from measurement mode to correction mode)
4) Body temperature measurement
Switch to body temperature mode, point thermometer at the center of forehead and
keep it vertical at distance of 1~3cm; press measurement button, measurement value
appears after about 1s; if the value exceeds alarm value ( 38 ° C by default) , and the
mometer lets out beeps.
3. Switch measurement mode
press “body/ correction” button to switch measurement mode
4. Alarm temperature setting:
Long press setting button for 2S, LCD screen displays F1 ( the original setting value
shows after 1~ 2s) , then press + / - button to adjust alarm temperature, 38 °C by
default.
5. Temperature unit setting:
Long press setting button for 2S, LCD shows F1, and then press setting button once to
display F2 ( the original unit is displayed after 1~ 2S) , and press + / - button to adjust
unit.
6. Body temperature correction settings:
Due to different skin color and skin thickness, there will be some differences in body
temperature ( surface temperature) , so it is necessary to add correction function; long
press setting button for 2S, LCD screen displays F1, then press setting button twice to
display F3 ( the original setting value is displayed after 1~ 2S) , and press + / - button to
adjust correction value. The default setting is 0.0 without correction.
For example:
Suppose the actual body temperature is 37.6°С. If the forehead tem
-
perature measured by this machine is 38.1°С , 0.5°С higher than actual value, the tem
-
perature value can be corrected by this method. In this example, after entering F3,
press - button to change the corrected value to “ - 0.5°С” .
Note:
After removing battery, thermometer powers off and restarts,
correction value will be restored to default value.
7. Buzzer switch setting:
Long press setting button for 2S, LCD screen displays F1, and then press setting button
three times to display F4 ( the original setting shows after 1~ 2S) , press + / - button to
adjust, LCD screen displays On or oFF at the same time.
8. Backlight indicator settings:
Long press setting button for 2S, LCD screen displays F1, and then press setting button
6
7
3
2
1
4
5
8
9
