Alarm Button
Down Button
Up Button
Rewind Button
Gear Button
Set up your AcuRite Iris
®
(5-in-1)
Direct-To-Wi-Fi Display
06100M
SETUP REQUIRES:
• Display
• Power Adapter (3 AAA backup batteries recommended)
• AcuRite Iris (5-in-1) Sensor*
*May be sold separately and requires 4 AA batteries
1
INSTALL SENSOR BATTERIES
In the outdoor sensor battery compartment, install four
AA alkaline or lithium* batteries.
*Lithium batteries recommended for temperatures
below -4°F (-20°C).
NOTE: In the battery compartment of the sensor, there is
a small A-B-C switch that must match the selection on the
display. By default, both the sensor and display are set to
“A” and should not need adjustment.
2
PLUG IN DISPLAY AND CONFIGURE
SETTINGS
Plug in the power adapter. Configuration will begin
automatically once the display is on. Use the Up button
and Down button to select between options, and press
the Gear
button to confirm your selections.
• RF Channel A-B-C (A is recommended)
• Auto Daylight Saving Time (ON/OFF)
• Clock Format (12-hr or 24-hr)/Hour/Minute
• Month/Day/Year
• Units of Measurement (U.S. Standard/Metric)
› Temperature Units (°F/°C)
› Wind Speed Units (mph, km/h, knots)
› Rainfall Units (in./mm)
› Pressure Units (inHg/hPa)
You can configure these settings at any time by pressing
the Gear
button. Wi-Fi configuration is optional, but
recommended.
3
MOUNT SENSOR
Find a suitable place outdoors to mount the AcuRite Iris
Sensor:
• At least 5 ft. (1.5 m) off the ground
• With the front solar cell facing south
• Away from heat and humidity sources
• Level for accurate rain reporting using bubble level on
top of sensor
For additional information on the best way to mount your
AcuRite Iris, please refer to the AcuRite Iris instruction
manual or visit: support.acurite.com and navigate to the
AcuRite Iris (5-in-1) Weather Station category.
A B C
A-B-C Switch
Set to match
display
Install Batteries
4 AA Batteries
Rain Gauge Stabilizer
Remove and discard
If you are interested in accessing your weather data anytime, anywhere online, follow the below steps to push
your weather data to the internet. If you are only interested in viewing your weather data inside your home on
the display, then disregard this section.
ADDITIONAL NOTES
The Wi-Fi signal on your display is broadcasted for 30 minutes after the display is powered on. Press the Gear
button
to reactivate the Wi-Fi signal broadcast at any time. Please note, however, that the display will not indicate that its Wi-Fi
signal is broadcasting. Check your settings on your setup device for the display’s Wi-Fi signal.
To retain Wi-Fi configuration details, backup batteries are strongly recommended for the display. The display can be power
cycled at any time to clear Wi-Fi credentials, records, and other settings. Simply remove the batteries, unplug the display,
replace the batteries, and plug the display back in to power cycle the unit.
Visit acurite.com/support for additional help on Wi-Fi Setup.
1
CONNECT TO DISPLAY’S TEMPORARY
NETWORK
Once the display is on:
• Open the Wi-Fi settings of your Wi-Fi-compatible
device and select and connect to the Wi-Fi network
with “AcuRite” in its name.
› If you see any “unsecure network” warnings,
know that it’s safe to continue.
› You will not be able to access the internet while
connected to this “AcuRite” network.
2
ACCESS WI-FI SETUP PAGE
Once connected to the Wi-Fi network with “AcuRite”
in its name:
• Open a web browser on the device you used to
connect to the display.
• To access the AcuRite Wi-Fi display setup page,
type the following into the address bar and then
press go/enter/return: 192.168.4.1
• Troubleshooting if the setup page does not load:
› Make sure you are still connected to the AcuRite
Wi-Fi network you connected to in step 1.
› Unplug the display, plug it back in, and try
setup again.
› Contact Support at acurite.com/support
3
ADD YOUR WI-FI CREDENTIALS
Once the setup page loads:
• Select your personal Wi-Fi network name, enter
your network password, and press
Save
.
• If Wi-Fi credentials are successfully entered, the
Wi-Fi indicator on the display should appear as:
• Troubleshooting if the setup page does not load:
› If the Wi-Fi icon flashes blue and appears
alongside a flashing X — Wi-Fi still needs to be
configured on the display. Repeat Wi-Fi steps 1-3.
› If a blue flashing X appears next to the Wi-Fi icon
— Wi-Fi credentials may be incorrect and should
be reentered. Repeat Wi-Fi steps 1-3.
4
SET UP YOUR MY ACURITE ACCOUNT
Once you see “Successfully connected to your Wi-Fi”
on your device and the Wi-Fi icon on the display fills
in solid blue:
• Reconnect your device to your normal, personal
Wi-Fi network.
• Download the My AcuRite app or visit myacurite.com
to complete setup.
› Note: The Device ID needed to set up your product
online is located on the back of the display.
Connect to My AcuRite
®
with Wi-Fi
SETUP REQUIRES:
• Display
• AcuRite Iris Sensor
• Wi-Fi Wireless Network (2.4 GHz networks only, not operable with 5 GHz)
• Phone, Tablet, or Computer with Wi-Fi Access
