background image

Page 1

 

© 2023 ABB. All rights reserved.

 

BDFB Gateway_QSG

 

Rev. 2.0

 

QUICK START GUIDE

 

Ethernet Gateway for BDFB Meter

 

QUICK START GUIDE

 

VIM1EC meter and Gateway Assemblies may be factory or field installed in BDFBs.

 

Models for Field Installation

 

Gateway Assemblies 

-

 not required when used with GPS system equipped with Millennium® II or Pulsar Plus 

controller or when Gateway Assembly is factory mounted.

 

150047915 for H569445 G101 BDFB 

 

150050054 for H569445 G103 BDFB

 

150050351 for H569445 G7 and G8

 

VIM1EC meter 

-

 not required when factory mounted

 

150050350 for H569445 G7 and G8

 

150050178 for H569445 G101 and G103

 

 
 

Warning: Hazardous energy and voltages are present in a powered BDFB. Avoid contact with the DC buses.

 

When making connection to energized DC buses place insulating material to prevent contact with other DC buses and grounded metal.

 

Before getting started, have the following tools and information available:

 

• 

IP Address and other network information from Systems Administrator

 

• 

PC or Laptop with RS

-

232, and Easyview2* installed

 

• 

RS

-

232 cable

 

• 

Torque wrench 

-

 0

-

240 in

-

lb / 28 Nm (Gateway installation only)

 

• 

Screw Driver 

-

 Phillips #2 (retrofit only)

 

• 

Socket 

-

 

5/16” 

(retrofit only)

 

*EasyView2

™ 

is the graphic user interface (GUI) ABB provides for local serial port access to controllers (see 

Reference Documents).

 

Installation Steps

 

Ethernet access to BDFB Meter VIM1EC may be implemented via a Gateway card (factory

-

installed or 

 

field

-

installed), or via a Millennium® II or Pulsar Plus controller.

 

Start with the step indicated in this table for the equipment that you are installing.

 

 

 

Installing

 

Start with Step

 

Skip if

 

Gateway Assembly

 

R1

 

Not installing a Gateway Assembly

 

VIM1EC Meter

 

V1

 

Not installing a VIM1EC Meter

 

VIM1EC Meter

 

Gateway Assembly 150047915 and 150050054

 

Gateway Assembly 150050351

 

Summary of Contents for VIM1EC












Reviews: