AAQ AutoLift AL-900DD Installation Manual Operating Instructions Download

Page: 1 / 34

Advance AutoQuip

2 McDonald Crescent | Bassendean WA 6054

Ph: 08 9279 1663 | Fax: 08 9279 1667 | E: [email protected] | W: www.aaq.net.au

- READ THE ENTIRE CONTENTS OF THIS MANUAL BEFORE

INSTALLATION AND OPERATION. BY PROCEEDING YOU AGREE THAT

YOU FULLY UNDERSTAND AND COMPREHEND THE FULL CONTENTS

OF THIS MANUAL. FORWARD THIS MANUAL TO ALL OPERATORS.

FAILURE TO OPERATE THIS EQUIPMENT AS DIRECTED MAY CAUSE

INJURY OR DEATH.

Specifications subject to change without notice.

Note: While all due care and attention has been taken in the preparation of this document, Advance AutoQuip shall not be liable for any inaccuracies or omissions

which may occur therein

2 POST HOIST

AutoLift

AL-

9000DD

mmetric 2 Post Baseplate Vehicle Hoist

4000Kg

Maximum Lifting Capacity

Design Registration Approval Number:

WAH21203

Design Code: AS1418.9-1996

INSTALLATION MANUAL & OPERATION

INSTRUCTIONS

READ FIRST

DO NOT use the

machine until you read

and understand all the

dangers, warnings and

cautions in this manual.

Summary of Contents for AutoLift AL-900DD



































Search results

Summary of Contents for AutoLift AL-900DD

Reviews:

Related manuals for AutoLift AL-900DD

Brands by name

Popular brands

AAQ AutoLift AL-900DD, Installation Manual Operating Instructions

Search results

Summary of Contents for AutoLift AL-900DD

Reviews:

Related manuals for AutoLift AL-900DD

Brands by name

Popular brands