ZyXEL Communications IES-1248-51 User Manual Download

Page: 71 / 385

IES-1248-51 User’s Guide

Chapter 7 Introducing the Web Configurator

7.5 Changing Your Password

After you log in for the first time, it is recommended you change the default administrator
password. Click

Basic Setting

and then

User Account

to display the

User Account

screen.

Figure 27

User Account

Click the index number

to edit the default administrator account settings.

Config Save

Use this screen to save the device’s configuration into the nonvolatile memory

(the IES-1248-51’s storage that remains even if the IES-1248-51’s power is

turned off).

Table 4

Web Configurator Screens (continued)

LABEL

DESCRIPTION

Summary of Contents for IES-1248-51


































































































































































































































































































































































































Search results

Summary of Contents for IES-1248-51

Reviews:

Related manuals for IES-1248-51

Brands by name

Popular brands

ZyXEL Communications IES-1248-51, User Manual

Search results

Summary of Contents for IES-1248-51

Reviews:

Related manuals for IES-1248-51

Brands by name

Popular brands