ZyXEL Communications IES-1248-51 User Manual Download

Page: 68 / 385

IES-1248-51 User’s Guide

Chapter 7 Introducing the Web Configurator

Figure 25

Type

admin

in the

User Name

field and your password (default:

1234

) in the

Password

field. Click

. The main screen appears.

This is the web configurator’s main screen.

Figure 26

Home

- Click the menu items to open submenu links, and then click on a submenu link to open the

screen in the main window. See

Section 7.4 on page 69

for more information.

- Click this to open the

Home

screen. (This is the same screen that is displayed above.) See

Chapter 9 on page 81

for more information.

- Click this to log out of the web configurator.

Summary of Contents for IES-1248-51


































































































































































































































































































































































































Search results

Summary of Contents for IES-1248-51

Reviews:

Related manuals for IES-1248-51

Brands by name

Popular brands

ZyXEL Communications IES-1248-51, User Manual

Search results

Summary of Contents for IES-1248-51

Reviews:

Related manuals for IES-1248-51

Brands by name

Popular brands