ZyXEL Communications IES-1248-51 User Manual Download

Page: 69 / 385

IES-1248-51 User’s Guide

Chapter 7 Introducing the Web Configurator

7.4 Navigation Panel

In the navigation panel, click a menu item to reveal a list of submenu links. Click a submenu
link to go to the corresponding screen.

The following table briefly describes the functions of the screens that you open by clicking the
navigation panel’s sub-links.

Table 3

Navigation Panel Submenu Links

BASIC SETTING

ADVANCED APPLICATION

ROUTING PROTOCOL

ALARM

MANAGEMENT

CONFIG SAVE

Table 4

Web Configurator Screens

LABEL

DESCRIPTION

Basic Setting

System Information

Use this screen to display general system and hardware monitoring information.

General Setup

Use this screen to configure general identification information about the device

and the time and date settings.

User Account

Use this screen to configure system administrator accounts.

Switch Setup

Use this screen to set up system-wide parameters such as MAC address

learning and priority queues.

IP Setup

Use this screen to configure the system and management IP addresses and

subnet masks.

Summary of Contents for IES-1248-51


































































































































































































































































































































































































Search results

Summary of Contents for IES-1248-51

Reviews:

Related manuals for IES-1248-51

Brands by name

Popular brands

ZyXEL Communications IES-1248-51, User Manual

Search results

Summary of Contents for IES-1248-51

Reviews:

Related manuals for IES-1248-51

Brands by name

Popular brands