ZyXEL Communications IES-1248-51 User Manual Download | Manualshive

Page: 324 / 385

background image

IES-1248-51 User’s Guide

324

Chapter 49 ADSL Commands

An example is shown next.

The following table explains these counters.

Figure 215

15 Minute Performance Command Example

ras> statistics adsl 15mperf 10
Port 10 Current 15 Min elapsed time:833 sec (Link UP)
Current 15 Min PM: ATUC    ATUR
       lofs:     0     0
       loss:     0     0
       lols:     0     -
       lprs:     -     0
       eSs:     0     0
       inits:     0     -
       sesl:     0     0
       uasl:     0     0
History 15 Min PM-1: ATUC    ATUR
       lofs:     0     0
       loss:     0     0
       lols:     0     -
       lprs:     -     0
       eSs:     0     0
       inits:     1     -
       sesl:     0     0
       uasl:     0     0
History 15 Min PM-2: ATUC    ATUR
       lofs:     0     0
       loss:     0     0
       lols:     0     -
       lprs:     -     0
       eSs:     0     0
       inits:     0     -
       sesl:     0     0
       uasl:     0     0

Table 77

15 Minute Performance Counters

LABEL

DESCRIPTION

atuc

Upstream. These statistics are for the connection (or traffic) coming from the

subscriber’s device to the IES-1248-51.

atur

Downstream. These statistics are for the connection (or traffic) going from the

IES-1248-51 to the subscriber’s device.

lofs

The number of Loss Of Frame Seconds that have occurred within the 15-minute

period.

loss

The number of Loss Of Signal Seconds that have occurred within the 15-minute

period.

lols

The number of Loss Of Link Seconds that have occurred within the 15-minute

period.

lprs

The Number of Loss of Power Seconds (on the ATUR) that have occurred within

the 15-minute period.

eSs

The number of Errored Seconds that have occurred within the 15-minute period.

«
...
322
323
324
325
326
...
»

Summary of Contents for IES-1248-51


































































































































































































































































































































































































Reviews:

No comments

Related manuals for IES-1248-51

Brand: Optical Systems Design Pages: 12

Brand: Boca Pages: 52

Brand: Novatel Pages: 148

Brand: Tenada Pages: 9

G.SHDSL.bis 3010E

Brand: netsys Pages: 105

Brand: GE Pages: 5

Brand: Corecess Pages: 14

Brand: Zte Pages: 36

Hotwire 6310 MVL

Brand: Paradyne Pages: 17

Brand: Dynex Pages: 8

Brand: eLutions Pages: 76

Advisor RD 6203

Brand: Aritech Pages: 60

Brand: Zte Pages: 7

Brand: RACOM Pages: 27

Brand: Zte Pages: 9

Brand: Maxis Pages: 63

Brand: ICP Pages: 19

Brand: Lancom Pages: 66

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands