Z-Wave™ Configuration Parameters
You may use the below configuration parameters to change settings of the corresponding functionality.
2：Status LED Configuration
Paramter No: 2(0x02) Size:1 Byte
Value: 00(default) Output and the LED are in the different state.
Value: 01 Output and the LED are in the same state.
Value: 02 LED Always OFF
Value: 03 LED Always ON
3: Auto Turn-Off Timer
Paramter No: 3(0x03)， Size=4，
Values:0 (minutes) default;
Values: 1 – 65535 (minutes);
5: Auto Turn-Off Timer
Paramter No: 5(0x05)， Size=4，
Values:0 (minutes) default;
Values: 1 – 65535 (minutes);
8：Restores state after power failure
Paramter No: 8(0x08) Size:1 Byte
Value: 00 Output OFF.
Value: 01 Output ON.
Value: 02 (default) The state before a power outage.
9: Ramp rate（Local Z-Wave™）
Paramter No: 9(0x09)， Size=1，Default =1
Value=1 from 0x63 to 0x00 or from 0x00 to 0x63 need 1s
Value=2 from 0x63 to 0x00 or from 0x00 to 0x63 need 2s
......
Value=99 from 0x63 to 0x00 or from 0x00 to 0x63 need 99s
10: Multilevel minimum value can be set（Local Button）
Paramter No: 10(0x0A)， Size=1，Default =1
Value=0 disable
Value=1
Value=2
......
Value=99
11: Multilevel maximum value can be set（Local Button）
Paramter No: 11(0x0B)， Size=1，Default =99
Value=0 disable
Value=1
Value=2
......
Value=99
12:Double Tap Behavior---when switch is off and quickly press button 2 times, switch turns on to x brightness
Paramter No: 12(0x0C)， Size=1，Default =0
Value=0 enable double tap to full brightness (99)
Value=1 custom value set in parameter 18
Value=2 enable double tap to maximum brightness (turn on to the value relate with parameter 11)
Value=3 disable double tap to full brightness
15: Enable or Disable local / Z-Wave™ control
Paramter No: 15(0x0F) Size:1 ,Default =1
Value: 00 disable
(when paddle pressed switch will not turn light on or off BUT it will still control the light via z-wave™ and
it will change LED indicator status and on/off/multilevel status when paddle is pressed)
Value: 01 enable (normal operation like now)
Value: 02 disable local and Z-Wave™ control
(LED and on/off status will still change if paddle pressed) >>
make sure that status is still reported and LED indicator changes when Z-Wave™ control is disabled
16: dimmer speed (only for local press & hold)
Paramter No: 16(0x10)， Size=1，Default =5
Value=1 from 0x63 to 0x00 or from 0x00 to 0x63 need 1s
Value=2 from 0x63 to 0x00 or from 0x00 to 0x63 need 2s
......
Value=99 from 0x63 to 0x00 or from 0x00 to 0x63 need 99s
20: Association reports
Paramter No: 20(0x14) Size:1 ,Default =2
Value: 00 Z-Wave™ control：Multilevel report (without each level,just final level)
Manual control (short press): Basic report(without each level,just final level)
Manual control(long press & relay enable): Basic report(without each level,just final level)
Manual control(long press & relay disable): Multilevel report (each level will be reported)
Value: 01 Z-Wave™ control：Multilevel report (without each level,just final level)
Manual control (short press): Basic report(without each level,just final level)
Manual control(long press & relay enable OR disable): Basic report
Value: 02 Z-Wave™ control：Multilevel report (without each level, just final level)
Manual control (short press): Multilevel report (without each level, just final level)
Manual control (long press & relay enable): Multilevel report (without each level, just final level)
Manual control (long press & relay disable): Multilevel report (each level will be reported)
21: Disabled Relay Behavior
Paramter No: 21(0x15) Size:1 ,Default =0
Value: 00 report on/off and multilevel status when paddle is pressed and change LED indicator status and
Parameter 15 is set to value 0 or 2 (output control disabled) according to setting in Parameter 20
Value: 01 DON’t report on/off or multilevel status or and change LED indicator status when paddle is pressed and
Parameter 15 is set to value 0 or 2 (output control disabled).
22: Night Mode Brightness Level---Set the level of brightness the dimmer will turn on to when off and held Button for 2 seconds
Paramter No: 22(0x16) Size:1 ,Default =0
Value: 00 disable function
Value: 01-99
23: LED Indicator Color
Paramter No: 23(0x17)， Size=1，Default =1
Value=0 White
Value=1 Blue
Value=2 Green
Value=3 Red
26: LED Indicator Brightness
Paramter No: 26(0x18)， Size=1，Default =1
Value=0 Bright (100%)
Value=1 Medium (60%)
Value=2 Low (30%)
