background image

Zakład Wytwórczy Aparatów Elektrycznych Sp. z o.o.

8

2.4. Basic technical parameters

No.

Parameter

Value

1.

Rated operating voltage

72,5 [kV]

123 [kV]

145 [kV]

172 [kV]

245 [kV]

363 [kV]

2.

Rated current

1600 [A]

2500 [A]

3150 [A]

4000 [A]

1600 [A]

2500 [A]

3150 [A]

4000 [A]

1600 [A]

2500 [A]

3150 [A]

4000 [A]

1600[A]

2500 [A]

3150 [A]

4000 [A]

1600 [A]

2500 [A]

3150 [A]

4000 [A]

1600 [A]

2500 [A]

3150 [A]

4000 [A]

3.

Peak current

125 [kA]

125 [kA]

125 [kA]

125 [kA]

125 [kA]

125 [kA]

4.

Short-circuit current, 1 sec.

50 [kA]

50 [kA]

50 [kA]

50 [kA]

50 [kA]

50 [kA]

5.

Test voltage (50 Hz) for insulation:

- to earth and between phases,

- between contacts of one pole.

140 [kV]

160 [kV]

230 [kV]

265 [kV]

275 [kV]

315 [kV]

300 [kV]

315 [kV]

460 [kV]

530 [kV]

560 [kV]

750 [kV]

6.

Surge test voltage for insulation:

- to earth and between phases,

- between contacts of one pole.

325 [kV]

375 [kV]

550 [kV]

630 [kV]

650 [kV]

750 [kV]

650 [kV]

790 [kV]

1050 [kV]

1200 [kV]

1175 [kV]

1450 [kV]

7.

Radio interference voltage

<1000 [µV]

<1000 

[µV]

<1000 

[µV]

<1000 

[µV]

<100 [µV]

<250 [µV]

8.

Rated mechanical operating life:

2000  

cycles

2000 

cycles

2000 

cycles

2000 

cycles

2000 

cycles

2000  

cycles

9.

Dedicated operating mechanism:

- motor,

- manual.

NSO80

NR-5

NSO80

NR-5

NSO80

NR-5

NSO80 

NR-5

NSO80

NR-5

NSO80

10. 

On / off capacity (inductive and ca-

pacitive load) - version with arcing 

contacts, 100 cycles

-

2 [A] 

(up to  

76 [kV])

-

2 [A] 

(up to  

152 [kV])

2 [A] 

(up to 

 225 [kV])

Summary of Contents for ONIII





















Reviews: