Zte ZXSDR R8882 L268 User Manual Download Page 5

Page: 5 / 65

About This Manual

Purpose

This manual gives introduction on the product description, technical indices, and product

installation.

Intended Audience

Hardware Installation Engineer

Operation and Maintenance Engineer

Prerequisite Skill and Knowledge

To use this document effectively, users should have a general understanding of wireless

telecommunications technology. Familiarity with LTE wireless network and its related

components is helpful.

What is in This Manual

Chapter

Summary

Chapter 1, FCC Statement

Introduces the FCC statements that this device complies

with

Chapter 2, Product Overview

Describes product characteristic, interfaces, indicators

Chapter 3, Product Technical Indices

Describes the technical indices of the product

Chapter 4, Product Installation

Describes installation and cable connection of the

product

SJ-20110104194923-001|2011-01-19(R1.0)

ZTE Proprietary and Confidential

Summary of Contents for ZXSDR R8882 L268


































































Search results

Summary of Contents for ZXSDR R8882 L268

Reviews:

Brands by name

Popular brands

Zte ZXSDR R8882 L268, User Manual

Search results

Summary of Contents for ZXSDR R8882 L268

Reviews:

Brands by name

Popular brands