manualshive.com logo in svg

Zte ZXHN H268A, Maintenance Management Manual

Share
Download
Zte ZXHN H268A Maintenance Management Manual Download Page 47

ZXHN H268A Maintenance Management Manual(EXETEL)

RA

Service

11. Click

RA Service

to open the

RA Service

page, as shown in

Figure 5-17

.

Figure 5-17 RA Service Page

12. Configure the

RA

service parameters.

Table 5-9

lists the RA service parameters.

Table 5-9 Parameter Descriptions for the RA Service

Parameter

Description

RA Service

Enable or disable the RA service.

Specify MTU

MTU configuration mode.

l

On

The MTU is specified by the user.

l

Off

The MTU is specified by the system.

Preference

The preference of RA packets, value range: high, middle, low.

Min Retry Interval

The minimum time allowed between sending unsolicited multicast

Router Advertisements from the interface. (The value must not be

greater than 0.75 * (Maximum Retry Interval )).

Max Retry Interval

maximum time allowed between sending unsolicited multicast

Router Advertisements from the interface.

M

Managed flag.

Select this check box to enable the connected devices to obtain

the IPv6 address through DHCP IPv6.

O

Other configure flag.

Select this check box to enable the connected devices to obtain

DNS address through DHCP IPv6.

5-12

SJ-20150916162339-007|2017-02-16 (R1.0)

ZTE Proprietary and Confidential

Summary of Contents for ZXHN H268A

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands