manualshive.com logo in svg

Zte ZXHN H268A, Maintenance Management Manual

Share
Download
Zte ZXHN H268A Maintenance Management Manual Download Page 27

Chapter 4 Configure the Internet

Parameter

Description

Egress

Specify the data traffic direction. The ingress option and

egress option cannot be the same.

à

If the ingress is LAN, the egress should be a WAN con-

nection. The data traffic direction is upstream.

à

If the ingress is a WAN connection, the egress should be

the LAN. The data traffic direction is downstream.

3.

Click

Apply

button to apply the changes.

l

Configure IPv6 filter.

1.

Click

IP Filter – IPv6

to open

IP Filter – IPv6

page, see

Figure 4-7

.

Figure 4-7 IPv6 Filter

2.

Configure the IPv6 filter parameters.

Table 4-5

lists the IPv6 filter parameters.

Table 4-5 Description of the IPv6 Filter Parameters

Parameter

Description

IPv6 Filter Switch

Select

On

to enable the IPv6 filter.

Select

Off

to disable the IPv6 filter.

Name

Name of the IPv6 filter item.

The name must be specified.

Mode

Specify to discard or permit the data packages.

Protocol

Protocol name, including TCP, UDP, TCP and UDP, ICMPv6,

Any.

Select the protocol that needs to filter packets.

By default, it is

TCP

.

4-13

SJ-20150916162339-007|2017-02-16 (R1.0)

ZTE Proprietary and Confidential

Summary of Contents for ZXHN H268A

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands