manualshive.com logo in svg

ZOTYE JNJ7155, Quick Start Manual

The ZOTYE JNJ7155 is a cutting-edge vehicle designed for adventure seekers. With our Quick Start Manual, you can easily get acquainted with all its features, ensuring a hassle-free experience from the get-go. Download the manual for free from manualshive.com now and unleash the full potential of your ZOTYE JNJ7155.

Share
Download
background image

 

 

068 

Combination instrument

 

 

Hazard warning lamp 

 

 

 

Hazard warning lamp 

Function description 

 

Warning light of low oil pressure 

When the vehicle is started, the light flashes and makes audible alarm. Please stop the 
vehicle,  shut  off  the  engine  and  contact  with  authorized  service  station  for 
troubleshooting. 

 

Warning light of brake failure 

ABS  failure  warning  light  and  brake  failure  warning  light  are  illuminated  at  the  same 
time in case of brake system failure. The light is also illuminated in case of low brake 
fluid level. If the light is permanently illuminated, you have to depress the brake pedal 
heavily  and  it  requires  longer  braking  distance.  In  such  condition,  please  come  to 
authorized service station for troubleshooting. 

 

Driver’s  safety  belt  unfastening  alarm 
lamp 

When the start switch or ignition switch is turn to ON, if the driver fails to wear the belt, 
the light keeps flashing. When vehicle speed is above 25km/h, the buzzer alarms (100s). 
The light does not go off till the driver wears the belt. 

 

* Warning light of front passenger failing 
to wear the seat belt 

When the start switch or ignition switch is turn to ON, if the front seat is occupied and 
the front passenger does not wear the belt, the light flashes to remind the passenger of 
wearing the belt. The light goes off when the passenger wears the belt correctly. 

 

Warning  light  of  engine  exhaust  system 
failure 

When the start switch or ignition switch is turn to ON, the light is illuminated for 3s and 
then  goes  off.  If  the  light  is  permanently  illuminated  or  illuminated  during  driving,  it 
indicates  failure  of  engine  exhaust.  Please  contact  with  authorized  service  station  for 
troubleshooting. 

 

Warning light of engine system failure 

It  is  illuminated  inn  case  of  engine  system  failure.  Please  contact  with  authorized 
service station for troubleshooting. 

 

Warning light of low fuel level 

It  is illuminated in case of  low fuel level.  You can  drive for a certain  distance in such 
condition and you shall come to the nearest fuel station for refueling. 

 

Summary of Contents for JNJ7155



































































































































































































































































































Reviews:

No comments

Related manuals for JNJ7155

Camcar 40000 Manual preview
40000
Brand: Camcar Pages: 6
Eaton Green Motion Building Quick Start Manual preview
Green Motion Building
Brand: Eaton Pages: 12
Jeep PATRIOT 2013 Specifications preview
PATRIOT 2013
Brand: Jeep Pages: 5
Jeep PATRIOT 2012 Specifications preview
PATRIOT 2012
Brand: Jeep Pages: 6
Jeep Grand Cherokee SRT 2014 Operating Manual preview
Grand Cherokee SRT 2014
Brand: Jeep Pages: 345
Jeep Grand Cherokee 2015 User Manual preview
Grand Cherokee 2015
Brand: Jeep Pages: 236
Jeep Grand Cherokee Quick Manual To Repairs preview
Grand Cherokee
Brand: Jeep Pages: 18
Jeep Grand Cherokee Quick Reference Manual preview
Grand Cherokee
Brand: Jeep Pages: 24
Jeep Compass 2015 Owner'S Manual preview
Compass 2015
Brand: Jeep Pages: 560
Jeep Compass 2013 Owner'S Manual preview
Compass 2013
Brand: Jeep Pages: 525
Jeep Cherokee 2019 User Manual preview
Cherokee 2019
Brand: Jeep Pages: 308
Jeep CHEROKEE 2017 Manual preview
CHEROKEE 2017
Brand: Jeep Pages: 86
Jeep CHEROKEE 2017 Owner'S Manual preview
CHEROKEE 2017
Brand: Jeep Pages: 638
Jeep 2022 CHEROKEE Quick Start Manual preview
2022 CHEROKEE
Brand: Jeep Pages: 9
Jeep 2014 Patriot Service Information preview
2014 Patriot
Brand: Jeep Pages: 51
Jeep Jeep Wrangler Buyer'S Manual preview
Jeep Wrangler
Brand: Jeep Pages: 4
Jeep Jeep Wrangler Owner'S Manual Supplement preview
Jeep Wrangler
Brand: Jeep Pages: 50
Jeep Grand Cherokee SRT 2014 Owner'S Manual preview
Grand Cherokee SRT 2014
Brand: Jeep Pages: 118

Brands by name

Popular brands

Load more brands