manualshive.com logo in svg

ZOTYE JNJ7155, Quick Start Manual

The ZOTYE JNJ7155 is a cutting-edge vehicle designed for adventure seekers. With our Quick Start Manual, you can easily get acquainted with all its features, ensuring a hassle-free experience from the get-go. Download the manual for free from manualshive.com now and unleash the full potential of your ZOTYE JNJ7155.

Share
Download
background image

 

 

Driving instructions 

161 

Safety 

Handling 

Driving Guide 

Operating Guide 

DIY 

Technical Data 

Index 

 

* Starter switch 

 

 

 

To turn on the internal power supplies or to start the engine, the valid 
remote  key  has  to  be  inside  of  vehicle  and  could  be  detected.  The 
starter switch has four gears: OFF, ACC, ON and START. 

 

 

OFF: 

The power appliances are not powered on. 

ACC: 

The accessories, such as the cigarette lighter, are powered on. 

When  the  starter  switch  is  at  “OFF”,  press  the  starter  switch,  and 
meanwhile  do  not  depress  the  brake  pedal  (for  the  vehicle  equipped 
with  automatic  transmission)  or  the  clutch  pedal  (for  the  vehicle 
equipped  with  manual  transmission),  so  that  the  starter  switch  could 
go back to ACC. 

Caution ! 

If  the  Start  switch  is  kept  at  ACC  all  the  time,  the  battery  may 
become dead, resulting in the vehicle start. 

 

Summary of Contents for JNJ7155



































































































































































































































































































Reviews:

No comments

Related manuals for JNJ7155

Vaisala MD30 Setup Manual preview
MD30
Brand: Vaisala Pages: 24
ABL Wallbox eM4 Single Installation Manual preview
Wallbox eM4 Single
Brand: ABL Pages: 68
OCTO SmartDiag2GO GD201-O User Manual preview
SmartDiag2GO GD201-O
Brand: OCTO Pages: 5
Prorack K383 Fitting Instructions Manual preview
K383
Brand: Prorack Pages: 14
Axxess AXGMLN-08 Installation Instructions Manual preview
AXGMLN-08
Brand: Axxess Pages: 8
BGS technic 40108 Manual preview
40108
Brand: BGS technic Pages: 5
Oldsmobile 1999 88 Owner'S Manual preview
1999 88
Brand: Oldsmobile Pages: 344
ABL eMH3 Installation Manual preview
eMH3
Brand: ABL Pages: 66
Curt Manufacturing 31048 Installation Instructions Manual preview
31048
Brand: Curt Manufacturing Pages: 6
Metra Electronics 95-8202 Installation Instructions Manual preview
95-8202
Brand: Metra Electronics Pages: 20
Audi 2011 A3 Sportback Pricing And Specification Manual preview
2011 A3 Sportback
Brand: Audi Pages: 29
Thule 1809 Instruction Manual preview
1809
Brand: Thule Pages: 4
Honda 2006 Accord Owner'S Manual preview
2006 Accord
Brand: Honda Pages: 569
Thule 953000 Instructions Manual preview
953000
Brand: Thule Pages: 8
Xingyun XY40EV Service Manual preview
XY40EV
Brand: Xingyun Pages: 74
AutoLoc SB3PR Series User Manual And Installation Manual preview
SB3PR Series
Brand: AutoLoc Pages: 6
Coolster CHALLENGER GK-6125A 2018 Manual preview
CHALLENGER GK-6125A 2018
Brand: Coolster Pages: 45
Renault CAPTUR 2019 Vehicle Instruction Card preview
CAPTUR 2019
Brand: Renault Pages: 11

Brands by name

Popular brands

Load more brands