Zorlu ADB-9010 User Manual Download Page 5

*Before you take pot, fry-pan etc. from the hob, 

put their lids on. 

*Do not leave hot oil on the hob. Pots that have 

hot oil in them may cause selfignition.

*Pay  attention  to  curtains  and  covers  during 

cooking  of  meals  like  frying  because  oil  may 

flare up.

*Make  sure  that  filters  are  changed  in 

convenience.  Filters  that  are  not  changed  at 

appropriate time has risk of causing fire due to 

oil that will be gathered on them.

*Do  not  use  filter  materials  that  are  not  flame 

resistant instead of filter.

*Do not operate your product without aluminum 

filter; do not remove filters when the product is 

on.

*In case of flame, cut power of the product and 

the  cooking  appliances.  (Cut  power  of  the 

product by plugging it off the socket).

*Your product may cause fire risk if cleaning is 

not applied periodically.

*Cut power of the product before maintenance 

process. (Cut power of the device by unplugging 

it)

*When  chimney  hood  and  the  appliances 

working  with  energy  other  than  electricity  are 

operated at the same time, negative pressure in 

the room should not be more than 4 Pa (4 x 10 

bar)

*If  there  is  an  appliance  working  with  fuel  or 

gaseous fuel at the same place with your hood, 

this appliance's exhaust should be isolated from 

its volume totally and the appliance should be 

hermetic type.

*When  chimney  connection  is  applied  to  your 

product,  use  ducts  of  150mm  or  120mm 

diameter. Duct connection should be as short as 

possible and should include few bends.

*This product is designed for usage at home.

*Your  products  usage  voltage  is  220-240 

Volts~50Hz

*Grounded  plug  is  used  at  your  product's 

electric  network  cable.  This  cable  should 

definitely be plugged in a grounded socket.

*All  electrical  networks  should  be  set  by  a 

qualified electrician.

*

Installation applied by unauthorized people 

may  cause  the  product  to  operate  at  low 

performance,  damage  of  the  product  and 

accidents.

*

Power supply cable should not be exposed 

to press or smash during montage. Network 

cordon  should  not  be  placed  near  the 

cookers; it may cause fire if it melts.

*Do  not  plug  into  the  socket  before 

installation of the product is completed. 

*Keep the plug at a reachable place so that 

you can unplug it in case of any danger.

*Do not touch the lamps when they are on for 

long time. Lamps may hurt your hand as they 

will be hot.

*Kitchen  cooker  hoods  are  designed  for 

usage  during  normal  and  home-style 

cooking.  If  it  is  used  for  other  purposes, 

failure  risk  occurs  and  it  will  be  out  of 

warranty.

*

Follow  applicable  rules  and  directions  for 

passing  out  outlet  air.  (This  warning  is  not 

valid for usage without chimney.) 

*Flaming foods should not be cooked under 

the product.

*Start your product after you put pot, fry-pan 

etc. on the hob. Otherwise high temperature 

may cause some parts of your product to get 

deformed. 

-5

5

WARNINGS AND SAFETY PRECAUTIONS

Summary of Contents for ADB-9010























Reviews: