Zoom ADSL X4 User Manual Download | Manualshive

Page: 36 / 64

background image

36

X5

ADSL Modem User’s Manual

Under Status, you will see WAN Status, ATM Status, PPP

Status, TCP Status, and MAC Table Status buttons. Clicking

any of these buttons displays pertinent information. Note: You

can’t make changes to the ATM or TCP Status pages; you can
make changes to the PPP and WAN Status pages.
If your provider is using Bridged or Routed IP Encapsulation, you
may be instructed to perform a Release/Renew operation to gain a

new, valid IP address. To do so, perform the following:

•

Highlight Release in the pulldown menu, and then click Save

Changes.

•

Highlight Renew in the same pulldown menu, and then click

Save Changes.

«
...
34
35
36
37
38
...
»

Summary of Contents for ADSL X4

































































Reviews:

No comments

Related manuals for ADSL X4

Brand: SEA Pages: 2

FSMODEM-CELLBASE

Brand: Federal Signal Corporation Pages: 16

Brand: Hama Pages: 7

Brand: Elastic Networks Pages: 32

Brand: Cygnus Pages: 6

Brand: Blonder tongue Pages: 12

Brand: Yifan Pages: 30

Brand: Yifan Pages: 41

Brand: Comnet Pages: 72

Brand: BT Pages: 20

INTERNET DSL MODEMS

Brand: Geetel Pages: 10

Brand: Hughes Network Systems Pages: 53

TigerAccess EE SMC7800A/VCP

Brand: SMC Networks Pages: 1

EZ Connect SMC7003USB V.2

Brand: SMC Networks Pages: 70

Brand: CommScope Pages: 76

Brand: Zhone Pages: 2

DG834v2 - ADSL Modem Router

Brand: NETGEAR Pages: 143

Brand: Sierra Wireless Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands