background image

13

Three Year Warranty

Project Fire Products warrants its 
enclosed Zonecheck flow-switch tester 
to be free from defects in materials 
and workmanship under normal use 
and service for a period of three years 
from date of manufacture. Project 
Fire Products makes no other express 
warranty for this flow-switch tester. 
No agent, representative, dealer or 
employee of the Company has the 
authority to increase or alter the 
obligations or limitations of this 
warranty. The Company’s obligation 
of this Warranty shall be limited to the 
repair or replacement of any part of the 
flow switch tester, which is found to be 
defective in materials or workmanship 
under normal use and service during 
the three-year period commencing 
with the date of manufacture. After 

phoning Project Fire’s number, 01889 
271271 for a Return Authorization 
number, send defective units postage 
prepaid to Project Fire, Pasturefields 
Industrial Estate, Pasturefields Lane, 
Hixon, Staffs, ST18 0PH. Please include 
a note describing the malfunction and 
suspected cause of failure. The Company 
shall not be obligated to repair or replace 
units, which are found to be defective 
because of damage, unreasonable use, 
modifications, or alterations occurring 
after the date of manufacture. In no 
case shall the Company be liable for any 
consequential or incidental damages 
for breach of this or any other Warranty, 
expressed or implied whatsoever, even 
if the loss or damage is caused by the 
Company’s negligence or fault.

Summary of Contents for 450





















Reviews: