background image

3

Install exterior assembly

A

IMPORTANT: Before installation, make sure the latch is fully retracted (in the unlocked position) . 

Route the cable below the latch and insert the cylinder tailpiece through 
the horizontal slot in the latch.

B

2 / 6

4

Install interior assembly

Insert the cable connector to 
the socket. Push the connector 
in firmly until it is completed 
seated.

B

Rotate the thumbturn and keep it in a vertical position.

Make sure the latch is still fully retracted (unlocked).

C

5

While the door is OPENED and UNLOCKED 
(latched retrated), load 3 AA batteries into the 
battery compartment.

NOTE:
For best results, use new, non-rechargeable Alkaline 
batteries only. Do not mix old and new batteries.

Reset the lock to teach the lock the orientation of the door.

A

Press and hold the Reset button. Do not 
release the reset button until you complete 
the next step.

B

Place the 4th battery and keep holding the reset button, 
until the latch bolt extend.

C

Test operation using backup key and thumbturn
for smooth rotation. If thumbturn doesn’t rotate, 
repeat step 4C, making sure the thumbturn in vertical 
position, and tailpiece in horizontal position.

D

IMPORTANT: Always run this step after installation. The motor will not operate before completing the step.

NOTE:  
If the latch doesn’t extend within 10 seconds, repeat step 
4C and 5A, making sure the thumbturn is always vertical 
and latch always retracted.

IMPORTANT: Do not load batteries until lock is completely installed.

IMPORTANT: Do not insert the physical key before and during installation.

Remove the battery cover.
Locate the slot at the bottom and use your fingernail or a 
flat head screwdriver to pry the cover up and pull it off. 

A

Secure the interior assembly 
with the supplied screws.

E

K

Secure the mounting plate with the supplied screws. 

D

J

Keep Parallel to door edge.

Horizontal

unlocked

Send the cable through the bottom horizontal slot in the mounting plate.

C

E

unlocked

G

F

tailpiece horizontal

Vertical

Summary of Contents for ZS01







Reviews: