20
21
Be sure to clean the product after each use.
If the plate is left dirty, it will burn and be difficult to remove.
Please wait until the product has cooled down enough before cleaning the parts other than the plate.
●
Never wash the Heater Set and Temperature Control Plug. (Doing so may cause malfunction.)
●
Do not use the following:
●
Detergents other than mild kitchen detergent, such as thinner and bleach. (Doing so may cause discoloration, cracks,
degradation or corrosion.)
●
Polishing powder, nylon brushes, scrub brushes, anything made with metal, eraser pads, hard nylon sponges and abrasive
cleaners. (Doing so may damage the surface.)
●
When using chemically treated cloths, do not rub too hard or leave them on the product for a long time as the surface of
the product may become damaged, or chemical reactions may occur.
●
Do not use a dishwasher or dish-dryer. (Doing so may causes scratches, deformation, and discoloration.)
●
When washing the Main Body Guard, be sure to remove the Heater Set. (Doing so may cause malfunction.)
●
Do not leave the plate dirty or use it while it is still dirty. It may become difficult to remove deposits and may scorch. Doing
so may also cause malfunction or fire.
●
Be sure to clean the plate after using acidic (vinegar) or salty (sauce, soy sauce, salt) ingredients.
(Not doing so may cause corrosion.)
●
Do not leave the Lid while it is dirty. (Doing so may cause discoloration.)
(1) Wash with a sponge moistened with diluted mild
kitchen detergent.
(2) After washing with water, wipe with a soft dry
cloth.
(1) Wipe off dirtiness with a cloth moistened
with mild kitchen detergent.
(2) Wipe with a cloth moistened with water
and wrung tightly.
(3) Wipe with a soft dry cloth.
Main Body Guard / Lid
Wipe with a soft dry cloth.
Heater Set (Heater and Receptacle) / Temperature Control Plug
When dirtiness sticks to the surface...
After soaking in lukewarm water for a short time, follow steps
(1) and (2) for cleaning.
Heater Set (Heat Shield Plate and Plate Sensor Cap)
(1) While the plate is warm, wipe off any dirtiness
with a soft paper or cloth.
(Use tongs, chopsticks or a similar tool to avoid the risk of
burns.)
(2) Remove the plate from the Main Body, soak it in
warm water and mild kitchen detergent for a
short time, and wash it with a sponge.
(3) After washing with water, wipe with a soft dry
cloth.
(1) Fill the cooled plate with hot water (so that the entire
surface is covered), turn on the power, and when the
water boils, scrape off the dirtiness with a soft-tipped
tool such as a plastic spatula.
(2) Cool the plate, discard the water, and wash with a
sponge moistened with mild kitchen detergent.
(3) After washing with water, wipe with a soft dry cloth.
Do not use a metal scrubber, etc. to clean it. (Doing so
may cause rusting and discoloration.)
If the surface rusts or discolors, the heat shielding will lose
its effectiveness, causing deformation of the Main Body
Guard or raising the temperature of the table or other
surface on which the Main Body is placed.
Deep Plate / Grilling Plate
If the dirtiness is too stuck on or the plate is cold...
●
After washing the plate, wipe it with a soft dry cloth before turning it on and heat drying it.
(After heat drying, be careful as the product is hot.)
●
Do not cool the plate suddenly by placing it in water, etc. while it is still hot.
(Doing so may deform the plate and cause malfunction.)
Do not wash the Heat Shield Plate with water
(no thorough washing).
When stacking plates, stack them in the order shown in the figure
on the right, with a soft material such as a cloth between them.
(Failure to do so may cause scratches on the surface of the plates.)
Deep Plate
Grilling Plate
Cloth, etc.
Plate cannot be removed
from the Heater Set
Is the Temperature Control Plug still
inserted?
Problems
Cause
Remedy
Cooked food is badly burned
Difficulty cooking food
Are you preheating sufficiently?
Is the plate clean?
Is the Heater Set/plate installed correctly? Please install correctly.
Clean the plate. (See p. 20)
Remove the Temperature Control Plug.
Please preheat sufficiently before you start cooking.
(See p. 16)
Insert the Temperature Control Plug completely and
securely so that the white semicircular markings on the
Release Buttons (2 places, one on each side) are both
completely visible. (See p. 15)
Insert the plug securely.
Is the plug securely inserted?
Temperature Control Plug
does not insert
Plate does not warm up
(does not turn on)
Storage
●
Be careful not to drop plates when carrying them.
Temperature Control Plug
gets hot
The Temperature Control Plug may become hot during cooking, but this is not abnormal.
Please check the following points
before calling for service.
CLEANING AND MAINTENANCE
TROUBLESHOOTING GUIDE
Length of the Power Cord
Rating
External Dimensions (approx. cm)
Weight
Temperature control range
Model No.
Electric Consumption
EA-KFQ20T
●
This product is not suitable for use in countries or regions with different power supply voltages or frequencies.
●
External dimensions are those of the product with the Deep Plate and Lid in place.
AC 220 V 50 Hz
1189 W
2.5
ｍ
48 (W) × 33 (D) × 14 (H)
Approx. 5.5 kg
Keep Warm to 240°C
SPECIFICATIONS
